We have low water pressure in our house (we are on city water).
-
Hudson Designs on Aug 04, 2011Hello Wendy, What was the pressure at the city side? Their side I would expect to be around 100 PSI. Your line pressure should be around 50-80 PSI. Over time a build up of scale in side older copper and metal pipes can cause the flow to slow down. This maybe your problem. You can get a pressure gauge and attach it to the hose bib to see the pressure there. Understand that Pressure and rate of flow are two different things. If you house is older you may think about having the service from the street replaced.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Aug 05, 2011Hudson has some very valid points here. Pressure and volume are different things. Even if you have pressure if the pipe delivery size is small, then your not going to get the volume out of the pipe. Ideal piping systems would have at least a 1 inch main coming into the house. 1 inch or 3/4 inch main pipes going to the hot water heater, and at least through the basement in which the pipes running to the fixtures tap into it. New construction uses 3/4 inch pretty much all the way to each fixture in the house. The older homes used 1/2 inch to the outside fixtures a lot. Nowadays 3/4 inch pipe is used. There are a few ways to get around this issue. Re-pipe all visible pipes in basement to larger size, or install a booster pump with storage tank. Both methods have their benefits and draw backs. In a local town near me, the street pressure is fine, but the volume of water is not. almost everyone has booster pumps in their system. Piping in the basement can be difficult to do, but with the invention of Shark Bites and or Pex tubing, you can do the entire job without doing any soldering at all. Installing a pump system is not out of the reach of many do it your self types but it is more involved and really should be done by a professional plumber. Pumps can be installed to service the entire home, or just your outside pipes.Helpful Reply
-
-
Hewitt Remodeling Services LLC on Aug 05, 2011Wendy, Excellent comments from Hudson & Woodbridge, especially the discussion on pressure vs volume. We could run the full gamut of advice but think it is best if we had more information first. A few questions... When was your house built? Are you on a crawlspace or a slab? Any of your immediate neighbors have similar problems or is it isolated to your house? How long has it been a problem? Is it getting worse? TimHelpful Reply
-
-
KMS Woodworks on Aug 05, 2011I'd be curious to know the numbers as well....they city said pressure is good...but did they provide a number. And how did they determine this? most main are buried deep under the street and there "measurement point my be blocks awayHelpful Reply
-
-
Paul M on Aug 05, 2011If you do what Hudson is saying and your pressure is good but your flow is not the you have build up in your pipes. If you don't know how to check your pressure you can get one of these and find out. http://www.amazon.com/Rain-Bird-P2A-Water-Pressure/dp/B00004RACK If your pressure is normal and your flow is still slow increasing your pressure won't help and it may damage some of your fixtures. If your pipes have build up in them I don't know what you could do besides replace them. Hopefully that is not the issue.Helpful Reply
-
-
French Remodeling on Aug 05, 2011If you have galvanized pipe in your house or as an entrance line then that is probably the problem. If you have a copper entrance line and copper plumbing in the house I would check the pressure regulater or backflow preventer.Helpful Reply
-
-
Ellen C on Aug 11, 2011Speaking of backflow preventer...that had crossed my mind as a potential culprit. There is a possibility that the valve has an issue. Also, if there is a master valve shut-off at the house (look in the crawl or garage), it may not be open fully. Also be sure that the valve at the meter is fully open. If water was ever turned off at the house for plumbing work or due to a vacant property, it's possible that the those may not be fully open....much easier to check the simple stuff first.Helpful Reply
-
Related Discussions
I found little pieces of rusty material in the bottom of my washing machine. We have iron in our well water,and wonder
if it could be building up somewhere and breaking off, or if the washing machine is rusting out someplace. It's about 20 yrs old, but still works good. Has anybody ha... See more
We have an old water stain on our ceiling...how do I cover it?
How do I remove the stubborn stains from gas stove?
How do I remove the stubborn stains from gas stove?
Is there any way to get scratches off of a plastic toilet seat cover?
How to make solar pool covers with pool noodles?
I saw small “Solar” pool covers made with pool noodles and black garbage bags. I was hoping to find the directions again.
How do we remove calcium deposits on our patio water fountain
How do we remove calcium deposits from our patio fountain and brick walkway?