I am thinking of flooring my attic, with the intention of using it as a storage area for now and possibly insulating it
-
KMS Woodworks on Dec 02, 2011I'd go with T & G ply...this is what is used for subfloors..Helpful Reply
-
-
Dennis B on Dec 02, 2011I'd use 1/2 - 3/4" exterior plywood. If need be it could be ripped into strips to fit through openings to put it in.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Dec 02, 2011We use OSB all the time in attics when we insulate. We stack 2x6 at right angles to the existing floor joists and place them at 24 inch centers. And as Dennis said we cut them in down as needed to fit. We do however use screws not nails to fasten. primary reason is the impact that the hammer has on the ceiling below can cause all sorts of nail popping which then requires repairs and paint. Using screws is a non impact way of fastening them down. Particle board is way to heavy and is not considered as a structural material for any type of span. Stick with OSB or plywood. What ever you can get for the best price.Helpful Reply
-
-
MCL on Dec 08, 2011Make sure the structure, i.e. truss bottom chord or ceiling joists, can take a storage load. Codes vary, but it's somewhere around 80 lbs./SF. Personally I agree with KMS and would use 3/4" T&G plywood, especially if you want to finish it with another flooring later.Helpful Reply
-
-
Glkirk Builders Inc. on Dec 09, 2011MLC has the prelims down. It is very important to be sure your joists are up to code. Now is the time to upgrade. Code says you need 3/4" . continious material. IE 3/4" T&G plywood or 3/4" T&G osb.Helpful Reply
-
-
Its Really Concrete, Inc. on Dec 09, 2011our garage is truss framed onsite 16" o/c - 2 x 6 bottom & 2 x 4's up the angles,,, the floor is 1/2 ply screwed down,,, heavy enough for storing the Christmas stuff, daughter's college banners, & spare luggage - tnx for the code update inf - however how would 1 upgrade joists to carry addl deadload of 3/4" t&g ply - sistering ? hometalk scores for me again !Helpful Reply
-
-
Tidewater Insulators on Dec 09, 2011Make sure you leave enough room for insulation under the flooring. Until you finish the room off, this could be a major area where you could loss heating through the ceiling. Compressing the insulation lowers the R-value and effectiveness.Helpful Reply
-
Related Discussions
Old desk with hard rubber top needs help
I have a very old desk that is in great condition except for the top. It is that old, hard rubber and it has a lot of dings and gashes (for lack of a better term). I ... See more
Do colors have to coordinate for bedroom and bathroom?
I recently got overzealous and bought a shower curtain, towels and rug for my bathroom in a totally different color than I planned on doing in the actual bedroom. Doe... See more
Should I remove plaster and lathe or can I just remove plaster?
I have an 1882 Balloon construction house that has some pretty extensive plaster falling off of the lath. I know that the lath actually adds to the wall stability, a... See more
How do I remove sand paint from the walls of a small bathroom?
Thought it was clever and a great look until I realized that if you fall against the wall it would scrape worse than a fall on cement. My husband is elderly and the l... See more
Has anyone had any luck removing artillery fungus?
Please provide personal success stories on how to get rid of fungus in mulch... not links because I have googled and watched others and tried. My daughter had a load ... See more
Which do you prefer: distressed wood or natural wood?
When it comes to choosing wood for your home decor, the finish can make all the difference in achieving the look and feel you want. Distressed wood, with its rugged c... See more
Repurpose glass crackle globes
I have several old solar lights with the glass crackle globe on top. The solar part doesn't work anymore. What could I do with the glass globes?