I am trying to replace a light ballast. They both have red wires coming out of thr right.
-
3po3 on Jan 14, 2012Can you take a picture of this setup? And I'm not absolutely certain what your question is.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Jan 15, 2012The wiring of this type of lamp must match the wiring diagram that is on the face of the new ballast. If it does not have one which most of them do, then you need to check with the manufacture of this product for the wiring diagram for this replacement unit. You must be sure that this is the correct ballast for the lamp size and type your using. Some have auto starts, some require a starter. What ever you purchased must match exactly what you currently have or you risk an explosion of the new ballast being put in. Here is a link that you can perhaps refer to. About mid way is wiring diagram. http://donklipstein.com/f-lamp.htmlHelpful Reply
-
-
LandlightS on Jan 15, 2012You have an electronic ballast that is replacing the old magnetic ballas (which are hard to find today thanks to Gov't regulations). It will work fine but you have to rewire the fixture to match the wiring diagram on the ballasts. Also check to lamp description: is this ballast for a T12 lamp or a T8 lamp (or both). If you decide not to attempt to rewire the fixture, either have an electrician install the ballast or return it and purchase a new fixture with an electronic ballast for just a few dollars more.Helpful Reply
-
-
LandlightS on Jan 15, 2012PS: hate to say it but the link from Woodbridge is outdated. It states that a 4 light fixture will have two ballasts and if you go to HD, Lowes or any Ace Hardware you will find a 4 lamp electronic ballasts that replaces the 2 old magnetic ballasts.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Jan 15, 2012Thanks Landlights, I will update my library accordingly. I would think however regardless of type etc. Does not the ballast have the wiring diagram on the face of it? That should answer his question I would think?Helpful Reply
-
-
LandlightS on Jan 15, 2012Yes, th ballast does have a wiring diagram, however they are always not that easy for a DIYer to understand. With the electronic ballast, the neutral no longer goes to the lamp holder, but to the ballast, and that is where it get confusing. If he were replacing a " rapid start" ballast, he would find the neutral connected to the ballasts.Helpful Reply
-
-
Don H on Jan 15, 2012Thanks Woodbridge and Landlights-Diagram helped , and not needing a neutral wire to the lamp holder.Helpful Reply
-
Related Discussions
Which room would you pick for a room makeover in your home?
We're curious, if you could redesign any room in your home, which is the room you would choose?Whether it's your cozy living room, your bustling kitchen, or even your... See more
Suggestions for a topper to cover just top of blinds?
We just painted the sunroom from sage green walls/ ceiling to this light beige walls and light blue ( tint of gray) ceilings. We Have to have blinds for the East morn... See more
How does one stop a shower curtain from sucking in and attacking you
It is so aggravating. I recently moved into an apartment with no shower "doors". Every time I shower the shower curtain is sucked into the shower and will not lay dow... See more
GNATS - How to get rid of them?
Somehow my house and garden got tiny gnats that killed my fuchsia plant and fly everywhere. I have tried ALL the Web recommendations - soap and oil dishes, sand in th... See more
Can I decoupage my toilet seat what is needed to do this?
I rent but I hate the carpet in my master bedroom what can I do?
The carpet is stained and gross I have lived here for 6 years. Should I rip it out and change it without asking my landlord or can I suggest that I will pay for putti... See more
Can I hang a dresser mirror on my bedroom wall?
How to use a mirror from a old dresser can it be hung on a bedroom wall?