I am trying to replace a light ballast. They both have red wires coming out of thr right.
-
3po3 on Jan 14, 2012Can you take a picture of this setup? And I'm not absolutely certain what your question is.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Jan 15, 2012The wiring of this type of lamp must match the wiring diagram that is on the face of the new ballast. If it does not have one which most of them do, then you need to check with the manufacture of this product for the wiring diagram for this replacement unit. You must be sure that this is the correct ballast for the lamp size and type your using. Some have auto starts, some require a starter. What ever you purchased must match exactly what you currently have or you risk an explosion of the new ballast being put in. Here is a link that you can perhaps refer to. About mid way is wiring diagram. http://donklipstein.com/f-lamp.htmlHelpful Reply
-
-
LandlightS on Jan 15, 2012You have an electronic ballast that is replacing the old magnetic ballas (which are hard to find today thanks to Gov't regulations). It will work fine but you have to rewire the fixture to match the wiring diagram on the ballasts. Also check to lamp description: is this ballast for a T12 lamp or a T8 lamp (or both). If you decide not to attempt to rewire the fixture, either have an electrician install the ballast or return it and purchase a new fixture with an electronic ballast for just a few dollars more.Helpful Reply
-
-
LandlightS on Jan 15, 2012PS: hate to say it but the link from Woodbridge is outdated. It states that a 4 light fixture will have two ballasts and if you go to HD, Lowes or any Ace Hardware you will find a 4 lamp electronic ballasts that replaces the 2 old magnetic ballasts.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Jan 15, 2012Thanks Landlights, I will update my library accordingly. I would think however regardless of type etc. Does not the ballast have the wiring diagram on the face of it? That should answer his question I would think?Helpful Reply
-
-
LandlightS on Jan 15, 2012Yes, th ballast does have a wiring diagram, however they are always not that easy for a DIYer to understand. With the electronic ballast, the neutral no longer goes to the lamp holder, but to the ballast, and that is where it get confusing. If he were replacing a " rapid start" ballast, he would find the neutral connected to the ballasts.Helpful Reply
-
-
Don H on Jan 15, 2012Thanks Woodbridge and Landlights-Diagram helped , and not needing a neutral wire to the lamp holder.Helpful Reply
-
Related Discussions
What could be causing a wet floor, if a plumber finds no leaks?
wet floor under sink dry iu and run water no leak? no smell all is clean. run water both tubs, garbage disposal, use sprayer everything underneath stays dry. Go away ... See more
How to keep critters from getting under a mobile home?
An animal got through the skirting on my mobile home and died. My place had a terrible odor for two months since I couldn't locate the intruder. Is there an easy way ... See more
What can I put on my wooden pool deck to minimize the hot surface?
What can I put on my wooden pool deck to minimize the hot surface. I do not want to use regular carpet as it holds water and my deck is hugh.
How can I protect my door-casing from my power wheelchair?
My doorways are being ruined by my power wheelchair. It's more than just scratches in the paint. I have deep gouges in the wood. Before I try to get these filled and ... See more
How do you get a suction cup bath mat to stick to the tub?
How do I decoupage old glass bulb covers from light fixtures?
I need ideas for updating hanging light fixtures in kitchen then have the brass colors and clear glass cone bulb covers. I’d like to decoupage the glass covers ?
How do you get rid of fruit flies from the soul of your plant?
There are fruit flies all over my plants.