How do I adjust a bedroom door so that it will close shut?
-
3po3 on Feb 18, 2012Do you mean it swings open or that it doesn't latch. For the former, try tightening the hinges. For the latter, in addition to the hinges, you might try moving the strike plate slightly to catch the door.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Feb 18, 2012Sandra, we need a bit more to answer that question. As Steve said there are several things that can be done, but we need to know a bit more. When the door is closed, or when you hold it closed. Does the top of the door match up even with the top of the opening? Does it appear to drop down over the side of the latch, or open up? Stand on the outside of the door and slowly close it. Does the door hit the trim somewhere and not somewhere else. Or do you simply have to push real hard on the door in order for it to latch?Helpful Reply
-
-
Sandra M on Feb 19, 2012Thank you for your help! The door hinges seem tight enough, but the top line of the door is not perfectly level. The latch is not matching the strike plate area. I have another door with same problem which will latch if I pull upwards on the door knob and push it closed. The first door seems to drop a tad too low. Do I just move the strike plate and chisel out a bit at the bottom? Seems my home is "settling" a bit causing this to happen. This is the greatest website I have ever found!Helpful Reply
-
-
Nichter's Home Services Corp on Feb 19, 2012resetting the latch striker plate is the short fixHelpful Reply
-
-
KMS Woodworks on Feb 19, 2012Sandra...one trick I do a lot with "sagging" doors is to install longer screws in the hinges on the jam. this "lifts" the strike side of the door up a bit and often allows the latch to engage.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Feb 19, 2012If its just a tiny amount you need to move the door up to aline with the latch, then you can do what Nichter suggested to reset the striker plate. But there is even an easier way. Take some old lipstick and put it on the end of the latch bolt coming out of the door. Put enough on it so when the latch hits the strike plate it will transfer to it. Open the door latch so it does not rub on the strike plate close the door the release the door handle so the bolt comes out and rests against the striker plate to leave a mark. Then open the door to see just how much is needed to get the latch to properly close. Using a Dremel tool, or even a small half round metal file, file away the strike plate enough to allow the door handle bolt to close as it should. Moving the plate is an option, but you need to cut into the door frame a bit and reset the plate. While this is fine, if the door gets worse over time you will eventually need to pull the door frame out of the wall and reset it or jack that area of the house up and that will require you moving the plate once again. I use the Dremel tool, the smaller hand grinder with a metal grinding tool attached. It makes fast work of the latch plate. If indeed the hinges are the cause of the sag then do as KMS said to use longer screws on the top hinge and tighten them up a bit more to pull the door up again.Helpful Reply
-
Related Discussions
How to get rid of mice?
We seem to have some unwelcome Mickeys and Minnies in our house. What is the best way to get rid of them?
How to remove popcorn ceiling with asbestos?
I want to remove my popcorn ceiling, but it has asbestos in it. How do I go about this safely?
How to caulk baseboard gaps?
How do I fill gaps at baseboard, should I caulk? If so, does anyone know how to caulk baseboards?
How to fix squeaky hardwood floors?
How do I fix squeaky hardwood floors?
What to do about closet doors that collide with bedroom doors?
My closet is small with two doors that open from the middle, but anytime left open and the bedroom door opens in slams into the closet door.
How can I fix the dog-eaten portion of my bedroom door?
My dog ate the bottom portion of my bedroom door. Can I fix it? how to? or is it best to just replace it?