drilling with carbide drill bit concrete wall
-
3po3 on May 28, 2012You might see if you can rent a hammer drill in your area, or borrow one from a particularly handy neighbor. That could make it easier.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on May 29, 2012Exactly correct Steve. The carbide drill is useless without the hammer drill. You simply cannot put enough pressure on the drill to allow the bit to drill into the block or cement. And if its solid concrete, you will burn up the bit long before you get one hole done. The hammer drill not only turns but it vibrates the drill against the wall causing the carbide bit to bite into the cement. Once you see how easy this is you will be amazed how fast it will work. Rental shops carry this type of drill for only around $20 for two or four hours time.Helpful Reply
-
-
Betty on May 29, 2012thanks guys, I knew something was not right with this picture. So, do you think we have already burned up this drill bit. I guess my own answer is go ahead and get another drill bit and really make it easyHelpful Reply
-
-
Betty on May 29, 2012will it be an electric drill or is it a pneumatic type thingHelpful Reply
-
-
KMS Woodworks on May 29, 2012Electric....I have 3 hammer drills. Two matching Dewalt 18 Volt cordless ones...and a big bad boy corded version. I'm assuming you are going to install some blue tapcon type screws?Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on May 29, 2012Electrical like KMS said. I is not to big of a drill to use. I doubt they rent the battery types anyway. It is typically a little larger then a regular drill that you may be using now. They also may end up renting you a slightly larger drill not at all like the one you are familiar using. They will show you how to use it, but other then being a bit bigger it pretty much works exactly the same and those you have now other then hammer.Helpful Reply
-
-
Betty on May 29, 2012Thanks you guys, yes, We bought the Blue tapcon screws and the drill bit even comes with the screws. I guess my next question. I just asked one of my handy friends. He did not have one, but said I needed a masonry/brick drill bit that carbide was for metal. So, do you think we are using the wrong drill bit too.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on May 29, 2012No TAPCONS are used for cement. You have the correct drill bit. You must get the hammer drill for this to work. You can tell if its the correct drill bit by the end of it. There should be two little pieces of metal, not real sharp like a normal drill that appear to be fastened to the end of the bit. That is the carbide cutting head.Helpful Reply
-
-
Betty on May 30, 2012thank you guys mission accomplished. my husband was able to borrow one from work and surprising how easy it was when you have right equipment. Also if I could put a plug in for the habitat restore stores. we went to one in our town on saturday and they had things marked down 50%. we found a gladiator garage wall system for 20 dollars. If you have never checked one out it is great and the money goes back to supporting the work of building more homes.Helpful Reply
-
-
KMS Woodworks on May 30, 2012As another plug for the habitat stores..... the one nearest me also rents tools at rate less than most other places.Helpful Reply
-
-
3po3 on May 30, 2012That's great, Betty. Glad you got the problem solved. Now you're ready for the shelves. Kevin, you and I need to look into getting a commission from Habitat for all the plugs we give them around here.Helpful Reply
-
Related Discussions
Need to hang curtains on concrete brick walls without drilling?
Electric stove burners not working? Need help!
I've run into a frustrating problem with my electric stove, as none of the burners seem to be heating up anymore. It's been quite a setback for my culinary adventures... See more
What’s your favorite flower?
Let's brighten up our day with some floral beauty! Flowers come in so many shapes, sizes, and colors, and everyone has a favorite. We want to know: What is your favor... See more
How do I get rid of mole/voles and chipmunks from my garden and yard
I want to get rid of a trumpet vine that is growing on my home.
How do you get rid of Trumpet Vine. It is growing into the foundation of my house. I have tried pulling it out, round up, vinegar and salt. Please share your knowled... See more
What can I do with this DVD stand?
I have a DVD stand that I am trying to repurpose instead of trash. Any ideas?
Huge tomato plants and no flowers!
Does anyone know the cause of my healthy looking tomato plants not producing flowers? I see no insects..water as needed (they're in huge containers) and plenty of af... See more