The top and bottom of the container.
How do I repair this?
This is a limited series rustic moose/bear stoneware utensil holder. I really don't want to toss it out so hoping someone can help with some ideas on how to repair it. For those of you reading this, learn from my lesson - if you have a stoneware utensil holder you want to keep around, place a thick rubber pad inside the container so when you accidently drop heavy tipped utensils into the container, it won't break it. Thanks!
I numbered each broken piece so that I know where each one fits together.
Yep. The entire bottom of the container broke off.
Related Discussions
How to get rid of mice?
We seem to have some unwelcome Mickeys and Minnies in our house. What is the best way to get rid of them?
How to remove popcorn ceiling with asbestos?
I want to remove my popcorn ceiling, but it has asbestos in it. How do I go about this safely?
How to caulk baseboard gaps?
How do I fill gaps at baseboard, should I caulk? If so, does anyone know how to caulk baseboards?
How to fix squeaky hardwood floors?
How do I fix squeaky hardwood floors?
How do I repair cracked leather car seats?
How to repair the cracks on both front seats of this 11 year old Volvo. FYI: the car lives in very dry Las Vegas, but is garaged.
First, you need to find a lid or a band to fit around the bottom. (band clamp would work), then use a porcelean glue to glue the small pieces together. Remove the clamp or lid and let cure for 72 hours. Once cured, you can glue it onlto the sides. Let cure for 72 hours. Then I would shellac the outside, letting dry upside down over a pole.
See above.
So sorry your special piece was damaged. Fortunately, the break doesn't look like it will show. How about picking up a piece of cushioned felt to first attach to the bottom (like the circles with sticky on one side you place under items so they don't scratch your furniture, only this comes in a solid piece). Cut felt piece to fit inside of bottom and attach, then glue your ceramic bottom together and glue that to the bottom of jar. This way you will have a little cushion when utensils hit the bottom from now on. Good luck! :)
I have done a lot of porcelain repairs -figurines -tea pots- planters- pottery and cups, I think it will glue together fine. Gorilla brand superglue actually has a nice applicator tip I might suggest using that. After the repair you may want to put a piece of foam ( they have thick fun foam that I love to use a a liner) or sponge on the inside bottom so there’s no traumatic re-injury.
Your brakes look very clean if there is any missing pottery I would suggest filling defects using eproxy stick it’s one of my favorite repair tools to have on hand. This go-to miracle repair tip is the Oatey epoxy putty stick. I find it easier to work with than bondo and this clay like putty can be sculpted and fill defects. It does harden in a few minutes and will dry a gray color can be sanded or drilled and will needing painting unless its final gray color works for your repair.
This two-part epoxy sticky-found at big box hardware stores in the plumbing department near the pvc purple glue. In a clear plastic red capped tube. I get mine at Lowes $6. Home Depots its version and JB Weld is another but more $ and smaller. Other smaller 2 part epoxy sticks options can also be found in the boat marine and wood repair shopping sections.
You mix -press -then you can use scrape off excess (I use depleted gift card) and/or sand and paint. Cured putty is strong enough to drill through.
I hope this helps!
I use gel super glue for ceramics and porcelain because they are porous. Liquid super glue for non porous surfaces. I only use Locktite.
I would take piece of vinyl - like you would use with a cricket or silhouette cutting machine or contact paper - place the pieces on the adhesive side (exterior to the adhesive). When you have everything in place, use some E6000 glue to fill in the cracker. The use some tape or elastic to pull the pieces together and hold them into place until the glue dries.
To everyone who helped me repair my limited series stoneware utensil holder, I want to shout out a huge THANK YOU for your ideas, suggestions and recommendations. Here is several pictures of how it looks now that it is repaired. I used glass glue, sticky back felt, Oatey Fix It Stick and spray shellac. I did place 1/4 inch rubber into the inside bottom of the holder so hopefully it won't get broken again.