I am thinking of flooring my attic, with the intention of using it as a storage area for now and possibly insulating it
-
KMS Woodworks on Dec 02, 2011I'd go with T & G ply...this is what is used for subfloors..Helpful Reply
-
-
Dennis B on Dec 02, 2011I'd use 1/2 - 3/4" exterior plywood. If need be it could be ripped into strips to fit through openings to put it in.Helpful Reply
-
-
Woodbridge Environmental Tiptophouse.com on Dec 02, 2011We use OSB all the time in attics when we insulate. We stack 2x6 at right angles to the existing floor joists and place them at 24 inch centers. And as Dennis said we cut them in down as needed to fit. We do however use screws not nails to fasten. primary reason is the impact that the hammer has on the ceiling below can cause all sorts of nail popping which then requires repairs and paint. Using screws is a non impact way of fastening them down. Particle board is way to heavy and is not considered as a structural material for any type of span. Stick with OSB or plywood. What ever you can get for the best price.Helpful Reply
-
-
MCL on Dec 08, 2011Make sure the structure, i.e. truss bottom chord or ceiling joists, can take a storage load. Codes vary, but it's somewhere around 80 lbs./SF. Personally I agree with KMS and would use 3/4" T&G plywood, especially if you want to finish it with another flooring later.Helpful Reply
-
-
Glkirk Builders Inc. on Dec 09, 2011MLC has the prelims down. It is very important to be sure your joists are up to code. Now is the time to upgrade. Code says you need 3/4" . continious material. IE 3/4" T&G plywood or 3/4" T&G osb.Helpful Reply
-
-
Its Really Concrete, Inc. on Dec 09, 2011our garage is truss framed onsite 16" o/c - 2 x 6 bottom & 2 x 4's up the angles,,, the floor is 1/2 ply screwed down,,, heavy enough for storing the Christmas stuff, daughter's college banners, & spare luggage - tnx for the code update inf - however how would 1 upgrade joists to carry addl deadload of 3/4" t&g ply - sistering ? hometalk scores for me again !Helpful Reply
-
-
Tidewater Insulators on Dec 09, 2011Make sure you leave enough room for insulation under the flooring. Until you finish the room off, this could be a major area where you could loss heating through the ceiling. Compressing the insulation lowers the R-value and effectiveness.Helpful Reply
-
Related Discussions
Painted wood: yay or nay?
Let's dive into the age-old debate: painting wood. Some homeowners swear by the transformative power of a fresh coat of paint on wood surfaces and furniture, while ot... See more
Why does my bathroom tub and sink sound like it's burping when I flush
This is new for us home, but built in 1959. Kitchen sink drains slow but have not heard burps.
Are gray walls here to stay or are they on their way out?
Hey everyone,Gray wall color has long been a favorite choice due to its versatility, modern appeal, and ability to complement a wide range of design styles.But the qu... See more
Quick, inexpensive fix to correct weathered,splintering wood on deck
My wooden deck is older, and the wood has started to darken and splinter. Outside of replacing the wood, is there anything I can do for a quick and inexpensive fix?
Looking for an idea to make the bookcase look flush against the wall.
It’s an Ikea Billy bookcase. The cut out for smaller baseboard doesnt work. Would like it to look flush with the wall. Would rather not have to cut the baseboard.... See more
How do I take off hard water from my tub?
Here’s my issue I have been living in the same apartment building for 18 years and I have a tub that deals with hard water on a daily basis. What is the best way fo... See more
How do I remove paint from painted tile and tub?
How should I remove paint from a tile floor and a bathtub?