How do you fill in a join in the crown molding?
![Jim](https://cdn-fastly.hometalk.com/resources/imgs-responsive/avatar-letters/avatar-J-F1C40F.png?size=91x91)
![](https://cdn-fastly.hometalk.com/media/profile/2017/07/08/27532639_1.jpg?size=50x50)
![](https://cdn-fastly.hometalk.com/media/profile/2017/04/01/15828040_2.jpg?size=50x50)
![](https://cdn-fastly.hometalk.com/media/profile/2020/07/09/1509692_2.jpg?size=50x50)
Related Discussions
How do you continue the crown molding around a stone fireplace?
![Joanne Wildy](https://cdn-fastly.hometalk.com/resources/imgs-responsive/avatar-letters/avatar-J-59A1F4.png?size=50x50)
Do you take down the stones and then do the crown molding. Is there a way to cut the stones so they will fit back?
Looking for an idea to make the bookcase look flush against the wall.
![Miami Pat](https://cdn-fastly.hometalk.com/resources/imgs-responsive/avatar-letters/avatar-M-F1C40F.png?size=50x50)
It’s an Ikea Billy bookcase. The cut out for smaller baseboard doesnt work. Would like it to look flush with the wall. Would rather not have to cut the baseboard.... See more
UPDATED (Pls See Latest Answr) Are these pipe hangers safe/suitable..?
![Tim](https://cdn-fastly.hometalk.com/resources/imgs-responsive/avatar-letters/avatar-T-605BE8.png?size=50x50)
Hello,I needed a pull-up bar and made one using two pipe hangers (1 1/2 inch openings) that I nailed into the ceiling joists with roofing nails and then put a 5 foot ... See more
How do i do away with the rosettes in the ceiling?
![Stevie Wood](https://cdn-fastly.hometalk.com/media/profile/2020/03/31/48869657_1.jpg?size=50x50)
Can you completely do away with the rosettes in the ceiling? I was thinking of doing a 2×3 across where the panels meet like a "farmhouse" look. (By cutting a 2x6 in... See more
I am wondering if you can trowel cement/concrete onto the shower walls
![Suelane](https://cdn-fastly.hometalk.com/media/profile/2016/01/27/4240915_4.jpg?size=50x50)
There is backer board, it will need the orange waterproofing membrane put on that but instead of installing tiles or a tub surround, can cement be troweled on to the ... See more
What sheen do I use for shiplap?
![Nichollesimmons](https://cdn-fastly.hometalk.com/media/profile/2016/10/23/3559981_1.jpg?size=50x50)
Putting Shiplap on back wall of 1/2 bath. Going with white and I was going to go satin, but I am seeing a lot of eggshell?
Caulk.
Normally Joints in crown moulding that are either faulty cuts or just the cut just didn't line up perfectly can be filled with white paintable caulking. Apply some caulk to the joint and use a small putty knife to push it in the crack following the profile of the moulding. I hope this helps!
joint compound will also work.
Sometimes this happens when there is settlement. I would use a caulk, followed by light sanding and touch-up paint. If possible, save some of the trim paint when the moulding is installed so you have a great match for touch-up.
It isn't easy to caulk a perfect seam - the caulk seam can sometimes be higher than the moulding, so I would sand it so the seam is perfectly smooth.
I agree with the previous posts recommending caulk. Caulk has an elastomeric quality that wood fill and joint compound do not. Joint compound and wood filler shrink as they dry and typically fall out.