How do I know if this oven plug meets irc building code?
Related Discussions
How to get rid of mice?
We seem to have some unwelcome Mickeys and Minnies in our house. What is the best way to get rid of them?
How to remove popcorn ceiling with asbestos?
I want to remove my popcorn ceiling, but it has asbestos in it. How do I go about this safely?
How to caulk baseboard gaps?
How do I fill gaps at baseboard, should I caulk? If so, does anyone know how to caulk baseboards?
How to fix squeaky hardwood floors?
How do I fix squeaky hardwood floors?
How to restore an old cast iron wood burning stove?
The story of this stove started in a small town in Mexico. It was in my mother's family and was used to cook on and heat the kitchen when she was a kid. When the home... See more
Help! I don't think my HE Kenmore washing machine is really washing!
I have read the manual, yet when I put a load in,they end up in a bundle ...especially sheets..everything is bundled inside,how can clothes get clean like this,with n... See more
I would contact a professional. I'm sure if you email a local company they can give you advice.
Call your township building code inspector. If it doesn't meet code they will tell you (and contact the contractor)
Go on-line with the manufacturer of your appliance and see what their installation manual says about connecting the power. You may get an idea of what needs to be done from there.
The clamp is just a strain relief to keep the cable in place. It isn't intended to seal the box. Your range will cover the plug. There isn't any way for a boil-over to affect it.
By building code the plug-in should be so far off flooring shouldn't be on the floor in the first place . someone probably didn't have enough wire to put it on the wall or didn't know how to get it inside the wall but either way it should be on the wall and up off the floor.
1) The picture shows a hard-wired connection, not a "plug".
2) Consult a licensed electrician. Do Not try to interpret the National Electrical Code on your own; you do not have the background knowledge.
3) The picture tells me this was a DIY installation - NOT done by a professional. Get it fixed. If there is a fire and your insurance company can lay the blame on this connection, they will not pay full restitution.
Please check into all of the above comments! That does not look safe.
Call an electrician immedeiately! It is worth the money to have it certified safe! Our gas and light company would send out somepne for free.
My home Was built new. Having issues getting reliable advice and why Iโm reaching out. Havenโt closed yet because of so many builder issues. The builder picked all the subcontractors and now I know why.
actually the electrician was the only one I trusted and now after finding this Iโm at a loss. Please help. Why donโt builders do everything to code? My contract states everything would be done according to code. The local code officials shrugged me off. Sad people get paid to protect the public and donโt do their jobs.
I agree that this is dangerous. Should not be that way. I definitely agree with Betsy. Sounds like the local inspector may have been paid off or missed the plug. Most builders do use their own sub contractors they are happy with. You should have been given a punch list to jot down what needs to be redone or repaired before closing on the property. Don't close until everything is repaired properly. You can also deal with your lender and homeowners insurance carrier if no one else will correct the problems. Good luck.
Carol,
Another thing to check is if your wiring for the stove is correct in your electrical panel. If your stove is rated for 50 amps, then your panel should show a dedicated circuit for just the stove with a tandem breaker (looks like 2 breakers connected with a bar) wired for 240 volts on a 50 amp circuit. Your stove might be rated for more or less so the circuit should match it. The IRC does not speak to specific wiring of appliances like stoves. The NEC defers to the appliance manufacturers installation requirements and speaks only to outlet placement if your stove has a corded plug and is not hardwired. The generally accepted practice in new construction is that all wiring and receptacles are mounted in such a way as to be contained within the cavity at the rear and bottom of the stove so the stove can go up against a wall without obstruction. The box and wiring in the picture may not be out of code other than it should be inside/under the stove.
Carol,
Everyone has excellent ideas that you need to seriously consider. I am sensing just through reading your letter that you live in a small town where everyone knows everyone else and everybody's business. I have lived in a town with 3500 people and lived in one with several million people. I have a reason for telling you this, and it is simply so you will know that I do understand what you are going through. Now, IF AT ALL POSSIBLE, RUN, DON'T WALK to the closest large town where you can find a House Inspector. One who has no connections to your town or the people in it. I really think that your town has a few "good ol' boys" that "help" each other out on such things as cheap substitutions for building materials, and the City code people ignoring you as they did. You need to bring in the Big Dogs. After you get a REAL House Inspector, you may find that you have grounds for, and need of, an Attorney (from out of town). I wish you good luck and hope everything turns out okay. ๐น๐๐