How do I replace the facing on my mobile home?

+4
Answered
My older mobile home is showing it's age.I need to give a face lift but am short on cash.How do I do it on a limited budget but make it look good.
q how do i replace the facing on my mobile home
Hardie board
q how do i replace the facing on my mobile home
Rain and sun damage
  7 answers
  • C. D. Scallan C. D. Scallan on Jul 04, 2017
    Have you tried just pressure washing it? If you have and you aren't pleased with that, you can always paint .

  • Jacky Jacky on Jul 04, 2017
    The original paint was applied to wet or uncured wood that had not been sanded prior to painting. You should remove the drip edge and pressure wash to remove the loose paint. Then you need to wait for a period of dry days. Then you need to get up there and sand down to fresh wood, following up with a tack-cloth to remove dust. Then apply a good primer and let it dry according to package directions. Then apply your chosen paint; I would recommend 2 coats with advised drying times inbetween. Pay attention to the drying time, and re-applying time from the paint manufacturer.

    OR, you could call a professional and have it wrapped in pre-painted aluminum, but you would likely be sealing in potential wood rot.


  • Dan21544285 Dan21544285 on Jul 04, 2017
    You have fungus/dryrot in the roof eaves. The metal flashing shows nails on the edge, which should have been nailed from the top side and been installed under the roofing. Looks like someone is trying to hide more damage below the metal flashing.
    DanDanTheTermiteMan

  • Doni G. Doni G. on Jul 04, 2017
    Looks like that cheap siding that is made of sawdust and glue and it has absorbed moisture. It really should be replaced with either wood or metal. Whatever the problem, it won't be easy or cheap. Consult with an expert who offers financing or contract payments.

  • Phenonw Phenonw on Jul 04, 2017
    I believe each one of these Very helpful people have the right idea. I can add one more idea, after you use these helpful ideas. If you have the regular roofing that trailers have (in other words Not shingles) you can coat the roof with a White
    roofing sealer/paint. This will lower the cost of AC BIG TIME!!! It will also seal the top edge of the flashing. We purchased ours from Sears but by now you should be able to find it at a building supply like Lowes.

  • Graham Hooper Graham Hooper on Jul 04, 2017
    Is it PAINT? or Some other Material? it Looks like Tree Branches have Hit it to Cause Damage to the Coating. And the Top Edge that has Sunk In Looks like Rot Below the Grey material. ... So If it is Paint then Use a Sander and Sand it Back to the Wood. Dont Water Blast as Water under Pressure will be Forced into the Cracks and into the Interior of the Framework.which Could cause the Framework to Rot. If it is Tar Paper or a Rubberized Product then Replace it with that. Use Silica Sealant in Any Cracks (Any Flexible Waterproof Sealant. .Use Bondi Fill or Epoxy Resin in the Rot Area After Scraping Out the Soft or Rotten Wood .then a Touch of Wood Preservative Paint to Cover what is Left and Prevent the Rot from Spreading. or Buy Metal Flashing ..Lift the other Metal Flashing Carefully Slide the New Metal Flashing Up under it (measure the Entire Width This Way the Metal will Take the Impact of the Branches .not the Wood Paint it Once it has Weathered .... Before it Starts to Rust But Use a Sealant at the Top Under the Lip As you Nail or Screw Down the Top Flashing Screws Maybe Better as the Nails May not Grip in Holes the Same Size

  • Marcia Ray Marcia Ray on Jul 04, 2017
    Had the same issue and had to replace the exterior siding and flashing. We also had to have a roofer come and make overhang eaves to prevent more damage to the roof and overhang. If you have insurance you may need to file a claim because it will be expensive. Good luck!