How to put a tough surface on a plywood sheet under my computer chair?
Related Discussions
How to get rid of mice?
We seem to have some unwelcome Mickeys and Minnies in our house. What is the best way to get rid of them?
How to remove popcorn ceiling with asbestos?
I want to remove my popcorn ceiling, but it has asbestos in it. How do I go about this safely?
How to caulk baseboard gaps?
How do I fill gaps at baseboard, should I caulk? If so, does anyone know how to caulk baseboards?
How to fix squeaky hardwood floors?
How do I fix squeaky hardwood floors?
Tile backsplash when there is existing countertop backsplash
We are thinking about how to add a backsplash to our kitchen. Unfortunately when we had our countertops installed we ordered a small backsplash that comes part way up... See more
Contractor mis-cut the floor when he put in the toilet
Hello, Our contractor didn't "measure twice, cut once" when he put in our toilet. Check out the photo. I'd appreciate any suggestions on a fix or a way to hide this m... See more
Hello Bob Gibson :) Cover the plyswood with linoleum. The link below is from theplywood.com and although I was thinking cover the plywood with epoxy, this link has a better suggestion (and much easier):
http://theplywood.com/chair-mat
Good Luck and thank you for coming toHOMETALK for a solution :)
You can purchase clear heavy plastic mats specifically designed to go under roller chairs to protect the flooring underneath, and also make it easier to roll. These mats are available in different sizes, in two common styles- to go over flooring, and to go over carpet.
In my opinion, to get one of these mats would be much faster and easier that trying to "make over" the plywood.
Agree with flipturn7, a visit of Office Depot ... they are a lot cheaper than plywood....I like the softer rubber ones with the teeth on bottom, they don't mat your carpet down and you don't go off rolling off at lightening speed. https://www.officedepot.com/a/browse/chair-mats/N=5+1211741/?hijack=chair%20mat&type=Search
iv had the mats as discribed above...they still "walk" when rolled over. I like the Lino idea.
If you want to preserve the look of the wood and make it look better in your master bedroom, I would clean it well, cover all of the nearby carpet and stain it so it looks like it was meant to be part of the room. Then seal it - at least 3 coats. There are some sealers that contain a stain so it seems like it would be 2 steps in 1, but you're still going to need extra coats of sealer and you can control the color of the stain better with a stand alone product.
You'll need to move your computer while you do this so that the sealer can fully cure - not just dry. Look on your can to figure out how long that will take. If you're ambitious, you could also put some molding around the edge of the plywood to upgrade the look a bit. Best of luck with your project. If you do it right it will upgrade the look of the plywood so it looks like it belongs.
You may be able to find less toxic products. The world is changing and we're finding less toxic products on the shelf all the time. Ask the staff from that department. They know their products. I'm not that energetic. I just like things to look nice. It would probably take me quite a while to do that project, so if I had to do it, I'd find a way to move the computer temporarily. (Fortunately I also have a laptop that I could use if needed) I wish you the best of luck and hope you find a solution that works for you!
Those might work. Just remember that rolling your chair wheels over it is hard on surface. Since you don't need a lot, you could also look for broken boxes where not all of the tiles are good but they are marked way down..
You may just want to go to an office supply store (like Staples) and buy a product made for this. They are not really expensive. AND a whole lot easier then what effort you are going thru. They are sometimes clear, so the carpet shows thru. Have had mine for years with no problems. This would way cheaper.
Bob, I was thinking that if you use cheap tiles you should definitely use a sealer. I know I mentioned it above, but cheap tiles might curl up after the chair rolls over them a number of times. Rather than wait and have it happen, then have another repair job on your hands, make sure you give it at least 3 coats of sealer and check the can for how long it takes to cure. It will dry relatively quickly so that you can add another coat, but that doesn't mean it's cured so it will be hard and durable. You might even find a 'cheap' rug at Ollies Bargain Store (if you have one in your area) and dress it up even more by putting a contrasting rug on top. Of course, you'll want one that doesn't have a high nap or a design the incorporates a change of nap on the surface. Take your time picking one out, always keeping in mind how your chair will roll over it. We did that in front of my hubby's computer because we have a new beautiful manufactured floor underneath. The floor is not supposed to scratch easily, but if your knew my sweet, hubby............ :)
More Good advice and thank you again Linda. There is more research to be done on my part. I have bought 2 different carpets in past. They did not work the way I wanted and I would have to glue one of them down or anchored the other with a different method. I decided to give the carpets to a Lady friend for her back yard patio. This has been an ongoing issue. The plywood works and the chair moves on it's smooth surface. That I like. But dark staining from shoes has made it look soiled. I can use rubbing alcohol again as I have done several times, but it is not 100 %. I will continue. Thanks..
Cover it with stick-on vinyl tiles.