Hi, Someone poured a concrete slab 14'x18' and left a really bad low
area against the house from the corner to the sliding glass door. So
now when I rinse it off it floods, and the person that did it won't answer there phone so I'm going to see if I can fix it can you please give me some advise on how to fix it ?.
The best way to fix this area is to have a Contractor who specializes in concrete, because with the technology we have today they can drill a few holes into the Concrete and raise the area up to the appropriate level.
Bobby is right. You can't just pour something on top of the low spot and expect it to stick to the concrete. That section of the pad may need to be cut out and re-poured. I am not familiar with the technique of drilling holes and raising the slab but I would certainly look into it if I were in your situation. I would also talk to a brick layer to see if they could cover the slab with bricks and make it drain. Fixes like these usually come down to what you can afford to pay out. But having the water puddle against your house is very bad. On a dry day caulk the seam between the house and the slab, that may help a little.
In my area they use a mixture of sand and water and the cost was far less then pouring a new slab. Are there witness marks on the outside of the house that would lead you to believe that the slab sunk after it was poured and cured? I can't tell by looking at the photo but it looks like there is a mark. If the slab sank you need to try and figure out why or you will end up with a sloped slab, again. Does your house have eave troughs and do they carry the rain away without overflowing the eave trough?
All you need do do is resurface the low spots with concrete resurfacer. Bobby is talking about slab jacking. They drill holes in the slab, pump concrete under the slab to raise it. Costs an arm and a leg and your first born. V Smith apparently hasn't heard about concrete resurfacing.
HiI'm in the middle of decorating my livingroom and I have an air vent in the floorboards can I block this up there is a void of about 8 to 10 feet below the... See more
I put down some carpet over the weekend and used Roberts 8015 universal carpet seam sealer on the carpet seams. However, I was not smart enough to realize you are... See more
I didn’t realize a small Coke bottle had turned over onto my new sisal rug, so much of it had soaked into the rug. I ended up needing a professional rug cleaning, but... See more
Installing carpet in new home. Had some evidence of dry wood termites so I hired a pest control company to spray. About a week later I noticed several almost... See more
We moved into my parents house after my father passed in 2016. Dad's response to any comment regarding needed repairs was "I 95 years old, what do I care" the kitchen... See more
I remember my mother using a hard Johnson’s paste wax from a round tin to shine her hardwood floors and then buff to a shine with an electric buffer.The liquid wax... See more
i removed 2 layers of linoleum tile squares ( from 1972) with a scrapper and there is a brown/black residue that is still on the foundation. How do I get it off, it... See more
I accidentally got fabric glue on my linoleum floor during a project. I didn't know it at the time so it dried well. Once I noticed I tried to clean it with... See more
I’m trying to conceal raised water pipes, a drain, and a raised electrical outlet in the floor. They’re about 8 inches above the floor. What can I do to cover
I had a larger area rug in my living area and recently replaced it with a slightly smaller one. I'm wondering how to restore the floor to be the same color. It's a... See more
Debi, different websites explaining how to.
https://m.youtube.com/watch?v=-uOg_0EiPbU#
https://answers.yahoo.com/question/index?qid=20070219183313AAeHYiA
https://m.youtube.com/watch?v=yrfX8zNgZEE#
The best way to fix this area is to have a Contractor who specializes in concrete, because with the technology we have today they can drill a few holes into the Concrete and raise the area up to the appropriate level.
Slab jacking costs an arm and a leg and your first born. Concrete resurfacing is low cost and a DIY.
Bobby is right. You can't just pour something on top of the low spot and expect it to stick to the concrete. That section of the pad may need to be cut out and re-poured. I am not familiar with the technique of drilling holes and raising the slab but I would certainly look into it if I were in your situation. I would also talk to a brick layer to see if they could cover the slab with bricks and make it drain. Fixes like these usually come down to what you can afford to pay out. But having the water puddle against your house is very bad. On a dry day caulk the seam between the house and the slab, that may help a little.
In my area they use a mixture of sand and water and the cost was far less then pouring a new slab. Are there witness marks on the outside of the house that would lead you to believe that the slab sunk after it was poured and cured? I can't tell by looking at the photo but it looks like there is a mark. If the slab sank you need to try and figure out why or you will end up with a sloped slab, again. Does your house have eave troughs and do they carry the rain away without overflowing the eave trough?
All you need do do is resurface the low spots with concrete resurfacer. Bobby is talking about slab jacking. They drill holes in the slab, pump concrete under the slab to raise it. Costs an arm and a leg and your first born. V Smith apparently hasn't heard about concrete resurfacing.
https://www.youtube.com/watch?v=lkl3bY7Z88k