Chipped tabletop
-
Z on Jul 31, 2013I can see why you want to repair this. It's gorgeous! You could buy the strips of wood veneer at HoDe of Ls to replace the missing piece. It's be a bit on the tedious side and wouldn't match perfectly, but certainly doable.Helpful Reply
-
-
Robin Pryor on Jul 31, 2013Yeah, I didn't even see it until I started sanding the top. It's actually smooth and flush with the rest of the table, but the difference in texture stands out like a sore thumb. I wondered if wood putty would help camouflage it, but I don't think that will do much to blend into the wood grain.Helpful Reply
-
-
Z on Jul 31, 2013Anything you do has a chance of still showing. Unless you are lucky enough to find a similar grain on the strips of veneer tape. It would look better than this though since the particle board will take stain differently than the wood veneer will. When sanding wood veneer in the future make sure to do it slowly. It's very thin and the pressure of a power sander can remove way more wood than doing it by hand so remember use a very light hand with very little pressure. Good Luck! Make sure you share finished pictures.Helpful Reply
-
-
Gail Salminen on Jul 31, 2013@Robin Pryor I am tagging @KMS Woodworks in the hopes you will find help there. Lots of good advice on this site from him. My only suggestion would be to use a thing strip of veneer as @Z has suggested. You would have to make it slightly larger so that you could sand the edges (by hand) to blend into the table. You would also need to know the type of wood in order to get the right veneer. Let us know what you do. It is a beautiful piece.Helpful Reply
-
-
Robin Pryor on Jul 31, 2013Thank you, ladies! I will keep you posted.Helpful Reply
-
-
KMS Woodworks on Aug 01, 2013Ouch...this is a classic example of a "sand through" the veneer on these tables is maybe 20 thousandths of an inch thick and a power tool can wreck havoc very quickly. The best repair would be to find some veneer that is a good match...I can say you will never get it perfect or even close, but better. And better is good. The best tool for doing this repair will be an Xacto knife. Here you would cut out the damaged area in a diamond or rectangle shape, then carefully make a "patch" to perfectly fit the hole. The more precise you are the better it will hide. With the patch made you would glue it in place with some quality wood glue, ( i use titebond III). Some very light sanding ( by hand) will even it up a bit. It look like the entire table top has some soiling , water staining and or mildew issues. So those will need to be addressed too.Helpful Reply
-
-
Robin Pryor on Aug 01, 2013Is the damage enough for me to walk away, or is it worth the repair?Helpful Reply
-
-
KMS Woodworks on Aug 02, 2013@Z I have to commend you on your fine "sketch" the outline you suggest would be the best as it would eliminate any perpendicular "cuts" to the grain lines that are not already present.Helpful Reply
-
-
Z on Aug 02, 2013Why thank you @Kevin. I feel quite honored in hearing that from you. You put a big smile on my face. Thanks!Helpful Reply
-
-
Becky Newberry on Aug 02, 2013some wood puttys are stainable ,i would try that first, would be an easy fixHelpful Reply
-
-
Robin Pryor on Aug 03, 2013Can you tell what kind of wood this is? Would that make a difference in choosing veneer?Helpful Reply
-
-
KMS Woodworks on Aug 03, 2013I'm leaning a bit toward "cherry" but the level of contamination from the water damage and mildew is masking it a bit tough to determine. http://www.veneersupplies.com/ the site above has a lot of pics, you might also try to track down a local Marquetry artist in your area. they may be able to help with the ID and provide the veneer you need. I have a stock of veneers, but nothing in Cherry. Some of my veneer is pictured in this article I wrote. http://www.networx.com/article/about-cabinet-facingHelpful Reply
-
Related Discussions
Patio umbrella keeps blowing over
Does anyone have a easy solution to keep opened patio umbrella from flying up and falling over even on a semi windy day? I have the heavy base, it's in a hole in a pa... See more
I am gluing some colored glass gems onto a glass window..
I am using E6000 to attach the glass gems to an old window. I want to make sure that everything will stay attached. I plan on spraying clear Krylon onto the whole gla... See more
How can I remove labels from coffee cans so I can upcycle them?
How can i keep neighbors small children from climbing my fence?
I have a 20 year old chain link fence set back on my property by almost a foot. The neighbors small children keep climbing it. I have talked to the dad and he doesn't... See more
How to get rid of bugs on raspberry bush without pesticide?
How can i upcycle rigid foam packing blocks?
how can i upcycle rigid foam packing blocks?
How do I get rid of moles, voles and chipmunks?
They dig holes, have tunnels and throw dirt all over. how can I get rid of chipmunks, voles, and moles with natural easy to find ingredients?