How do I do a DIY make over of my cheap tiled bathroom floor?
My bathroom has cheap floor tile that has separated. The area is maybe 4×7 with a clawfoot tub. I thought maybe grout or put something self leveling something. ( I'm not a DYIer) or paint/stencil or paint.
Related Discussions
How can I make over these bathroom tiles without replacing them?
I am renting an apt so cannot make drastic changes but really want to do something about my bathroom tiles. Can I paint over them or how can I change my bathroom look
How can I update old 1X1 inch bathroom floor tiles?
I hav very old tiny ceramic tiles. I want to update them without having to do the hard work of removing them. A stencil sounds great but every time I see it it’s on... See more
How can I make over an ugly terra cotta floor in my bathroom?
If I was going to do a bathroom should i put black tile in?
We have a bathroom that we are going to put black tile in
Best product for sealing very porous tile?
Hi fellow home talkers! How are all of you doing? If anyone could help me out...I would really appreciate it! We have a very porous PORCELAIN tile in our kitchen. ... See more
How do I remove vinyl tile adhesive that has leaked thru the seams?
These vinyl tiles have been our floors in our vacation retreat house for a few years. It began happening within a few weeks after installation. Of course we complaine... See more
How do i do this in
Hi Cheryl. It looks as if the grout is missing in places. I’d try using grout of the same color as the one previously used.
If the water has permeated what’s under your split & leaking floor, then you’ll have to scrape out with a pic of the damage & decay that’s making this gap grow. Anything you put over it will eventually fail, unless this is done.
Shop vac it as you go. Shine a light in there & see what’s left to re-adhere to. The idea is to epoxy it back down, Seal the heck out of it and then make it look pretty.
Sealing:
If it’s cleaned out & dry, then I would get a two-part epoxy with a syringe-type nozzle, waxed paper & 20+ bricks or concrete blocks.
Apply the epoxy into the crack, push it around for even distribution & then put the waxed paper on it and then load up the bricks to weigh it down.
Depending on what cure-time you bought, take off the bricks & see how it took. It may need more “brick time”.
When dry, clean the remaining cracks with rubbing alcohol and then fill with exterior grade paintable window/door caulk. Smooth with a wet finger.
Now you can paint any kind of stenciled or faux finish you want on it. There’s lots of tutorials on painting vinyl tile.
If your our time is worth a lot, skip the other cracks & install new peel & stick tile on top of this floor (once cleaned).
If you love this house & you’re going to stay here a long time, rip up the cheap tile & install a sheet vinyl flooring or a ceramic tile floor.
Good luck.
If it isn't coming up, you can grout it. I hate this type of tile because of this.
It looks as if you have "peel "n" stick" vinyl tile. Needs to come up. TIP; use WD-40 to remove. Raise corner, squirt it under tile, wait a few, run scraper under it. Takes up the adhesive too. Scrub floor good, let dry. You're now ready to get new floor. Idea; buy large ceramic tiles, clean them, let dry. Now for the fun part.! using permanent sharpies, scribble colors all over tile, squirt 91% alcohol on it, and strike a match, hold close to tile, -fire! - and watch what appears. Use these tiles to redo your floor. You will have a unique, one-of-a-kind floor, be the envy of everyone that sees it. Little bit of work, but oh my, the results you'll be getting.! I do this on 4 x 4 tiles to make coasters. Sells like wildfire.! GOOD LUCK.!!
Yes, these are 'vinyl peel and stick style' tiles, not ceramic. As they were originally put down with glue, not grouting, adding grouting will not help them from continuing to come up. With gaps showing that are this big, I too would be concerned about moisture underneath the whole floor.
This is a peel and stick floor and needs to come up. the WD-40 removal sounds good. See what is left and use that to determine the next step. Sheet vinyl would be an inexpensive item to use but may be difficult to install with the space. It would be better to go with easy to install vinyl plank which adheres to the floor and looks good.
Pull it all up and check the subfloor. If it's cement you are going to be ok, if not you might want to check for mold and other issues. So, if it's cement I would buy some spreadstone from Daich and put that down. Check it out, the stuff is awesome and low voc.
Vinyl tile that need to be removed. Warm it up with a blow dryer and it should pull up. Sink and toilet would need to be removed. Claw foot tub can be slightly raised with a car jack enough to remove and replace with new tile. Check the sub floor for any damage.
get at least 3 bids from the list from the better business burau...their workman ship has been verified.