Is there a way to patch drywall holes for reuse?
Drywall anchors for a shelving unit came loose-is it possible to patch up the original wall holes for reuse with anchors? I have considered moving the bracket; but it doesn't align with the other mounts on the wall-it will stick out like a sore-thumb. If this is possible, what are the different techniques and materials to achieve a strong enough bond for reuse?
Thank you!
Related Discussions
How to get rid of mice?
We seem to have some unwelcome Mickeys and Minnies in our house. What is the best way to get rid of them?
How to remove popcorn ceiling with asbestos?
I want to remove my popcorn ceiling, but it has asbestos in it. How do I go about this safely?
How to caulk baseboard gaps?
How do I fill gaps at baseboard, should I caulk? If so, does anyone know how to caulk baseboards?
How to fix squeaky hardwood floors?
How do I fix squeaky hardwood floors?
What's the best way to patch a hole in drywall with no stud behind it?
Best way to cover tack/staple holes in drywall
I have a question: we are going to re-do one of our bedrooms, it used to be our son's who had many, many posters etc tacked and stapled to walls. Other than wallpaper... See more
Hi ! You can spackle the holes to fill them , let it dry , then sand down to blend with the wall , then paint . But ...I wouldn't trust it to be used to screw into the same
spot ! I would move it over some ...but since you said you can't...we had this problem in our bathroom , where the towel bars pulled out of the wall . My husband came up with a great , easy solution . He screwed a piece of wood to the wall , into the wall studs , then the brackets for our towel rack can be screwed in to the wood !
you can see my tutorial , that I posted on this site called secure towel rack solution
good luck !!!
I wouldn't re-use it. I would move the anchor to a different area and patch for cosmetic purposes.
Yes you can but I would do a small patch rather than just fixing the holes. Cut a larger section out, until you get to the stud. Cut a piece of drywall to fit then screw in, tape,and mud. With a damp sponge, smooth the mud. Repeat 3x and paint.
As you have discovered the hard way, wall anchors have some real limitations when it comes to anchoring weight. If you absolutely have to mount in the same spot and cannot mount into wood, then the repair needs to be such that this doesn't happen again. A good way is to spread the weight out across the back of the drywall rather than having it concentrated on a small anchor spot. So ...
Cut out a 4" (approximate size, can be a bit larger) square of drywall around the hole. This will give you a bit of room to work and will make it easier to make a clean patch.
Cut strips from 1/2" x 2" wood that are at least 6" longer than your drywall hole is wide (even longer if there is room behind the drywall).
Slip the wood strip(s) through the hole and center it so you have 3" or more wood on either side of the hole. Make sure one wood strip is behind where your new wall anchor is going to be. Using drywall screws, screw through the old drywall and into the wood to mount it firmly.
With the wood in place you now have 1) an easy way to install your patch piece of new drywall, and 2) something that will spread out the weight of the shelving unit quite a bit.
Cut a piece of new drywall to fit the hole and patch & paint as usual.
When you mount the shelving unit again use drywall toggle anchor, installing the anchor so that the toggle lines up with the wood strip.
Hope this helps 😀
Did you use hollow wall anchors the first time?
I don't like the look of wood boards for supporting shelf brackets. Even painted they just don't look good. I like a clean look. I always use toggle bolts to hold shelf brackets that will take a lot of weight. The butterfly expands inside the wall.
https://www.homedepot.com/p/Everbilt-3-16-in-x-3-in-Zinc-Plated-Steel-Phillips-Mushroom-Head-Toggle-Bolt-Anchors-15-Pack-803922/204273381
Patching the hole and reusing it sadly isn't going to pan out. You can to through the effort of opening up the wall some and adding wood backing but that's a lot. Ideally go up or down if you can and use the screw in wall anchors, the type that look like large screws. Anything less than that will not be sturdy enough.
Ya you can patch it up with compound
compound would work
There is a product called rock hard putty you can get a lowes and it is cheap. A can is less then $10 and should last you for years. This would help seal all holes or gaps which would give you a finished look.