How do I fix this?
I have a lovely late 1940's vanity that belonged to my Mom. Unfortunately the top has numerous splotches and scratches on it. They weren't helped when my bottle of nail polish remover spilled in the very middle of the top surface ☹️. It's maple, solid, and I would like to make it look gorgeous again in it's "old" age.
What can I use on it? I am not a woodworker -I teach ELA to Middle Schoolers.
Thanks for your suggestions.
Related Discussions
Vinyl plank flooring vs pergo (laminate)
I currently have stinky dirty carpeting in my living room and I want to replace it with a durable flooring that can stand up to dogs and kids.
How to remove popcorn ceiling that has been painted?
Does having a paint over a popcorn ceiling change how I'd remove the popcorn ceiling?
How to apply peel and stick wallpaper?
I want to spruce up my walls with peel-and-stick wallpaper. Has anyone used this before and can advise me as to how to apply it properly?
How to stain wood floor?
I've heard staining is a good technique for updating floors. So how do I stain my wood floor?
I am repainting a table. Do I need to paint the underside?
The top of the table is stained ad dark color and is pine. Some drips are on the underside from the gel stain. The underside is also pine, but not finished and not pa... See more
How do I puff up leather couch seat cushions?
My favorite corner of the sofa is in need of some puffing up. Any ideas to bring it back to same as other seat cushions? It is uneven...
Sand and restain. First rub the nail polish in the direction of the grain with denatured alcohol. Use a putty knife to "lift off a bit as it softens" being careful not to scratch wood.
Use an orbital sander or sand by hand. Clean off all dust and debris with a damp rag. Use a rag dipped in stain with a SMALL amount of stain on it and rub it into wood in straight lines going with the grain.. A little stain goes a long way. You can always add a second coat but have to start from scratch if you put on too much.
Use Citristrip stripper to remove any finish. Sand it down to raw wood. Start with 100 grit sandpaper, then 150 grit, and finally with 220 grit. Wipe clean with a damp cloth. Stain if you want or just seal with three coats of a water based polyurethane.
https://www.hometalk.com/diy/bedroom/furniture/diy-refinished-wood-dresser-top-39188185
https://www.hometalk.com/diy/bedroom/furniture/you-need-this-simple-guide-to-refinishing-a-dresser-top-43281075
https://www.hometalk.com/diy/kitchen-dining/kitchen-dining-furniture/vintage-dining-table-top-redo-44318666
DIY Refinished Wood Dresser Top
You Need This Simple Guide To Refinishing A Dresser Top
Vintage Dining Table Top Redo
Citri strip is a non-toxic remover that will take it down to the wood. From there sand and dust it off with a damp microfiber cloth. The finish will be up to you. MInwax makes some excellent stains and is readily available at diy stores. Seal with thin coats of polyurethane.
Citristrip will work well to remove whatever finish your vanity currently has. A trick I've used is to apply the Citristrip and then gently cover witha plastic wrap and let the stripper work its magic for 20-30 minutes (or even longer if necessary). Then lift the plastic away and follow the instructions. After removing all the stripper, sand the vanity well to get a smooth finish. Then either stain or apply a clear sealer to protect the newly redone surface. It's so great to learn you are going to bing back the beauty of your Mom's maple vanity!
I agree, use Citristrip. Tape-off everything else and apply it to the top. Cover it with plastic wrap for a half hour. Use a plastic scraper to remove it.
If you sand and restain here is a helpful idea or two:
https://www.hometalk.com/diy/bathroom/vanities/staining-wood-vanity-vintage-renew-4191103?expand_all_questions=1
Giving a 1942 Vanity Table a New Life
Start with stripping the top. I would use citristrip. Then lightly hand sand with fine grit paper and clean with denatured alcohol. At that point, you can finish it to match. An old fashioned hardware store can help you match the color, most likely with a custom mix.
Also, clean the sides very well before you match it and remove any wax that is there.
Sanding should get you cleaned up. It might not remove every stain but it will help. Use a lower number to start, like 80 grit and work your way up to about 400 or so. You can then stain and seal for a refinished top.