Help with replacing plywood
How do you get the old plywood back off of a corner hutch to replace it? Someone cut a hole in the back of it and the bottom of both pieces of plywood are also damaged and they need to be replaced.
Related Discussions
Vinyl plank flooring vs pergo (laminate)
I currently have stinky dirty carpeting in my living room and I want to replace it with a durable flooring that can stand up to dogs and kids.
How to remove popcorn ceiling that has been painted?
Does having a paint over a popcorn ceiling change how I'd remove the popcorn ceiling?
How to apply peel and stick wallpaper?
I want to spruce up my walls with peel-and-stick wallpaper. Has anyone used this before and can advise me as to how to apply it properly?
How to stain wood floor?
I've heard staining is a good technique for updating floors. So how do I stain my wood floor?
Replacing "lost" legs on old rocking chair, help??
I have an old rocking chair that is legless but otherwise in great shape. How do I replace the legs - they do not have to be rocker legs - just plain legs that can ma... See more
Help with replacing kitchen Cabinet hardware, see photos
I want to update the hardware on my kitchen cabinets, but the old hardware has left a outline or shadow where the faceplates are. Looking for suggestions. My cabinets... See more
Can you see staples that you can remove? I would take a screw driver and remove them and then measure the wood and have some recut to put back on.
It’s nailed on☹️
If you could gently wedge a very very thin pry bar that should give you enough room to slowly and very gently remove that.
If all else fails could you just cover over the old plywood? If it was painted it would blend right in. Even if it was sanded and stained again that would also help this spot to blend in.
I would use the hole to help pry it off. If the wood is going to be replaced anyway, you don't have to worry about damaging it.
The easiest way to take it off is to use a mallet and gently tap the back piece from the inside of the cabinet. It is probably held on by small nails. If you are careful enough, you’ll be able to use the piece for your measurements for replacement piece.
to add....keep in mind that you can see the wood and it has been finished to match the cabinet. It will be easier to finish it before nailing on.
If the hutch is going to stay where it is, fill the holes and then wallpaper with a textured paper and paint or apply self stick wood flooring panels.There are so many other coverings to consider.
They are usually just attached with small nails. You should be able to pry a knife under one pieces and pry it loose.
Hello. Can you see the small nails on the backside? If you can you could try to pry them out with a screwdriver and or the opposing end of the hammer. Sometimes even needle nose pliers can be helpful. Alternatively you might try the approach of going on the inside of the cabinet take a block of wood and pound on it with a weighted hammer to see if you could push the nails outward and then go to the back side to see if nails have emerged and then you can pull them out
Hi Betty
Here is some info for your project
https://www.youtube.com/watch?v=9TEbLgvIqmk
That plywood is likely structural. You may have better luck covering it with something from the front - say wallpaper or beadboard panels. You could fill the holes and paint as well.
HI Betty, you should be able to use a flat headed screwdriver and slip it in between the frame and the back to pry it up a little. Once you have it pried up, you can use a hammer to remove the nails. (hopefully it isn't glued on!)
Plywood panels are normally installed with brad nails or other fasteners. A hammer can be used to move the back away from the frame enough to get in a be able to pry it away.
How is it attached?
Could you just fill with wood fill sand and paint them
It's nailed, stapled, or crown stapled on the back. Use a screwdriver and pliers to remove them.
It appears to be integral to the piece’s structure.
I would veneer over the holes.
It appears to be pine and you won’t find pine veneer.
If the costs of veneer shock you, then evaluate buying 1/4” plywood “project panels” - less than a full sheet.
it all depends how it is attached. but why take it off ? Refinsih whole piece .. it will be for sure safer
Get a strong putty knife and wedge in between the ply and the wood backing. Gently tap in with a hammer a lift to expose the nail head enough to get a small claw hammer around the nail head and remove. Keep going nail by nail until you can get it all off. Use the old wood as a pattern for new ply or save for another project.