How do I stop this leak?
I have a leak under the sink. I thought it was the supply line as the water was around that area. I replaced the supply line and it's still leaking. The problem wasn't the supply line. I know now that it is the pipe that feeds into the supply line. Where the dark brown putty (I assume) is. I don't know what these things are called. Can someone tell me so that I can ask for the right thing at Lowes/Home Depot?
The steel portion is the supply line. That screws onto the beige adapter (I assume that that's an adapter of some sort). Can I assume that the adapter is screwed onto that portion of the pipe where the brown putty is? I'm afraid that if I attempt to screw it off, that I will break it if it is not screwed on. That is definitely where the leak is coming from. Should I just get some plumbers pipe compound and put it where the brown putty is?
Related Discussions
How to get rid of mice?
We seem to have some unwelcome Mickeys and Minnies in our house. What is the best way to get rid of them?
How to remove popcorn ceiling with asbestos?
I want to remove my popcorn ceiling, but it has asbestos in it. How do I go about this safely?
How to caulk baseboard gaps?
How do I fill gaps at baseboard, should I caulk? If so, does anyone know how to caulk baseboards?
How to fix squeaky hardwood floors?
How do I fix squeaky hardwood floors?
How can I stop my sink from leaking and why vent inside? (stinky)
This just started a few weeks ago. When water runs from my 1/4 sink into the drain, it seems to back up and leak out of the pipe. This never happens with my 3/4 sin... See more
My kitchen sink has a slow leak every few weeks. Do I need a new trap?
is this the correct set up?
I would definitely try that. Possible the seal at that area isn't tight and that's why it is leaking.
It looks like some type of plastic pipe, but I have never seen that before. I would measure it and get a new coupling. The pipe needs to be cut and a new coupling installed. Turn off the house water supply, open the water valve to relieve residual pressure. Cut pipe close to, but clear of the brown gunk. The fitting will probably be a compression fitting and only require a couple of wrenches to get it installed. Then reconnect you braided hose and restore water.
Can't tell from the photo if the pipe where the adapter (brown putty) is steel or not. If it is steel pipe then the adapter is screwed into it. You need to unscrew the adapter from the pipe slather pipe joint compound on the threads and screw the adapter back on. If the pipe is copper (doesn't look like it is) then the adapter is soldered to the pipe. You would need to heat the adapter to remove it. Clean the pipe and adapter and resolder it. Make sure you use flux. If the pipe is plastic (PVC) then someone tried to glue it on with some kind of brown adhesive which won't work. (doesn't look like PVC). If you want to replace the adapter with a new one take a clearer photo and take it with you to Home Depot or Menard's and show them what you need. Any questions just reply.
I have had the faucet leak, drip down over the pipe and it looked like the pipe was leaking. Tightened the faucet and it was done. Hope you find your solution.
To me that looks like pvc or pex pipe. Depending on what the pipe is will determine the type of adapter to buy. My money is on that its pvc because it looks pretty old and pex hasn't been around forever. Turn off the water, cut the adapater off as evenly as possible and take it into your hardware store to find an exact replacement. If its pvc you will want to buy pvc primer and pvc glue to put the new one back on. Tip: screw the new adapter to your new supply line first and then glue it on to your pvc pipe.
Here is a site that tells you how to find exactly where the leak is coming from:
https://www.americanleakdetection.com/blog/2016/february/finding-the-source-of-an-upstairs-bathroom-leak/
If it is PVC pipe a metal adapter will not bond to PVC. It would have to be a PVC adapter. PVC glue melts both parts to create a bond.
GET A PROFESSIOLNAL PLUMBER IN THE LONG RUN ALL THE TIME YOU TRY TO FIX IT AND MONEY A PLUMBER SHOULD BE ABLE TO DO IT...GOOD LUCK
I would do two things before calling a plumber. I would get some plumbers white tape and put it around the threaded end. I would also put in a new washer.
Take the photo to Home Depot with you. I've done it several times.
i would ask a proffesional ... gasket is broken ..take a part and replace gasket