How to Build a DIY Kids Bookshelf (Homework Station)

Tools for this project

• Tape Measure
• Jig Saw
• Skill Saw
• Drill
• Worx Rotary Tool Kit
• Worx Air Brush

First, we need to write the names on the board before carving it out. To make the letter look nice, I printed out the names on a piece of paper and then traced it onto the board. If you have good handwriting skills you could just write the letters without tracing. 

Once the names are printed, flip it face down and color in the backside with chalk. 

Then place the paper on the board with the names facing up and trace the letters. Make sure not to move the paper during this process. When you trace the letters the chalk on the backside is transferred onto the board. Then remove the paper and you’ll see the letters on the board. If the letters are too light or have gaps, just correct it with the pencil.

Take the rotary tool and insert an attachment for carving wood. First, I used a straight attachment to carve out the perimeter of the letters. Then I used a ball attachment to carve out the letter. There are other attachments that you could use to make better or smoother lines. 

Take Worx Air Brush and add green color into the paint cup. Then spray the lower half of the letters. Next, add black paint and spray the upper half of the letters. Then take a roller with white paint and paint the board white, leaving the inner groove of the letter untouched. 

Now it’s time to make the shelf. Take 1×10 board and cut one top piece to 38″ in length, one bottom piece to 36 1/2″ and two sides pieces to 12 3/4″ in length.

Originally I wanted to build a standard shelf with typical sideboards. But I figured it would be nice to have something different than just a rectangle board. So I’ve cut out an arch in front of the side piece to give it a unique look.

Take the sideboard and in the front measure 4″ from the bottom and 1 1/4″ from the top. Now draw an arc that is 1″ deep. Then using a jig saw cut out the arch. 

You could modify this arch to any shape or size you want. Or you could skip this step altogether if you prefer just a regular rectangle board. 

Now cut the remaining pieces out of ¼” plywood. The backboard does not support any weight so there is no need to make it from ¾” board. 

Take 1/4″ plywood and cut backboard piece to 38”x13 1/2″. 

This shelf will be divided into three sections by adding two dividers inside the shelf. Again take 1/4″ plywood cut two divider boards to 12”x9 1/4″.

Even though the shelf boards will have weight on them the size of these boards are fairly small so I decided to use ¼” plywood. I didn’t want the shelf to be bulky.

Cut three shelf boards to 12”x 9 1/4″.

Since the ¼” plywood is very thin and attaching the shelf boards to the sides with screws was not an option, I had to make support boards for the shelf boards to lay on.  

Cut six support boards to 4”x9 ¼” using ¼” plywood.

Now it’s time to put everything together. Take the top board and pre-drill the pilot holes on the top for the screws. Since the screws are going to be very close to the edge, pre-drilling a pilot hole will prevent the wood from splitting. 

Apply wood glue and attach the sideboards using 1 ¼” wood screws. 

Place the shelf on the workbench facing down. Then attach the backboard to the sideboards and the top with 1 ¼” wood screws. The plywood typically does not split so pre-drilling pilot holes are not necessary for this step. 

Similar to step 11, when attaching the bottom board, pre-drill the pilot holes on the sides. Then apply wood glue and secure it with 1 1/2″ wood screws from the sides. 

Before inserting the shelf divider or the shelf board, glue two 4” tall shelf supports to the sides of the shelf. These supporting boards will be holding the shelf boards from sliding down. Clamp the support board and let it sit for a few hours until the wood glue dries. 

The divider boards need to have 4” tall support boards glued on both sides, see picture. Apply wood glue to the support boards and glue them together. Clamp the boards to the workbench and let it dry for a few hours.

Once the glue dries, insert the divider boards and the shelf board into the shelf. You could screw in the dividers from the bottom and the lower back to keep it from moving. 

Now attach the carved name boards to the top board of the shelf. Make sure to pre-drill the pilot hole so that wood does not split. You could paint the shelf any color you want or just leave it the way it is. You are done with a DIY kid’s bookshelf (homework station).