How to Build an Upholstered Floating Bench
![Brianna at Bloom in the Black](https://cdn-fastly.hometalk.com/media/profile/2020/05/12/43103625_3.jpg?size=91x91)
When I recently redesigned my girls' shared bedroom and realized the closet was no longer needed, we decided to turn it into cozy reading nook. And they were begging for big bed-like seating.
So I got to work building an upholstered floating bench and it was surprisingly easy! With even the most basic of woodworking skills you can make this too.
Measure the wall you’ll be installing your floating bench on. Since I was building the bench inside the closet, I measured the back wall from edge to edge and decided on the depth I wanted while still clearing the front edge of the closet (24″ in my case).
Once you have your measurements, determine how many 2x4s you’ll need in linear feet. You’ll need a back, a front, two sides, and a center brace. In my case, I had a 66″ closet so I needed two 66″ 2x4s for the front and back (66″ x 2 = 132″).
For the side and brace pieces, I butted the wood up to the front and back pieces so I needed that 24″ length less the depth of the front and back 2x4s (roughly 24″ – 4″ but 2x4s aren’t exactly 2″ deep. To make two side braces and a double thickness center brace, I needed 4 20" pieces (20" x 4 = 80")
You don’t have to be exact unless space constraints dictate you do). I used 20″ side and brace pieces so my bench technically ended up being 23″ with zero consequences.
So ultimately I needed 212″ linear inches of 2×4 i.e 3 pieces.
Decide how high you want your bench to be then mark a level line on the wall. Keep in mind that you need to add the height of the 2×4 (roughly 4″) plus the depth of the upholstery foam (3″ in this case).
For our closet reading nook, the girls wanted something fairly high up and I wanted to be able to slide their laundry basket underneath, so I measured for a 20″ under bench clearance:
20″ (clearance) + 4″ (board height) + 3″ (cushion height) = 27″ (top of bench)
Mark the wall where the top of the bench will reach.
Next, make a few more marks at the bench height then connect them with a straight edge. Use a level or this app to determine whether the line is level. How far off is it? If less than 1%, go with that. If it’s a lot — like in an old house — re-mark to a true level so the bench is comfortable. It may not be level to the floor but that’s the charm of old homes, right?
Make another level line three inches below your top line. This will be the line you align the 2×4 back brace to.
Use a stud finder to locate and mark the studs along the level line you just drew. It’s fine if you can’t drill into a stud for every screw, just be sure to use a wall anchor when there’s no stud. For a bench this length (66"), you want to hit a minimum of two studs on the back brace, and one on each side.
Hold the 2×4 along the bottom level line and draw a line down the face of the board from where you marked all the studs on the wall.
Using the stud lines you just drew on the board, drill pilot holes then 3″ screws into your back brace and into the wall. Use this same method I outlined for the back brace to level and drill the side braces into the sides of the closet.
Be sure to butt the side brace pieces directly up against the back brace.
Grab the other long 2×4 you cut (the front brace) and screw it into the side braces. Depending on how much room you have, you can do this with pocket holes, directly from the front of the piece, or using the metal corner braces we’re about to reinforce the whole frame with.
Note: Be sure to check for level, but if you hung the other braces correctly the front brace should automatically be level.
Use two 2x4s cut to the size of your side braces to create a center brace. This won’t be necessary for a shorter bench but in general, you should have a perpendicular brace every three-ish feet.
Add the brace using two of the corner braces to attach the center brace pieces to the front and the back. I didn’t use anything the “stick” the two boards together, just placed them right next to each other. I used two so I’d have a chunky center piece to attach the plywood top to.
Strengthen your floating bench frame by attaching a metal corner brace (or two) to each corner of the structure. You could opt to do this with pocket holes and additional screws, but I feel like the corner braces are easier, faster, and just as effective. If you’re prioritizing cost savings, go with the pocket hole method.
Cut your plywood sheet to the size of the bench top and attach with pin nails. You don’t need a ton since gravity is working in your favor, just enough to hold the plywood in place.
I opted to cut the plywood into two smaller pieces and use the center brace to attach the plywood along the center seam. This made it way easier to cut, transport, and fit the plywood into the second-floor closet space. Since we’re upholstering the top, the seam doesn’t matter.
Measure and cut your upholstery foam to the size of the bench. Not sure how? Read this quick post on cutting upholstery foam.
Measure your fabric and cut it semi-close to the final size you need. Use the length of the bench and add 3″ to each side (so the bench length plus 6″), and the bench depth plus 18″. That’s more than you need but better than not having enough fabric to work with.
Once you cut the fabric to size, find the center of the back edge of the fabric and make a mark on the wrong side, then also mark the center of the bench and a straight line 1.5″ – 2″ in from the back of the wall.
Using the line you just made, center the fabric and staple the back edge to the bench top.
Align the center mark of your fabric to the center mark on the bench top and staple the back edge, aligning the edge of the fabric to the back line you drew.
Staple first at the center and as close to the wall as you can. Add staples every few inches, pulling the fabric tight, until you’ve stapled all along the back edge.
Position the foam on top of the bench and push it as tightly against the back wall as you can. Then, pull the fabric to the front of the bench, wrap underneath the frame, and begin stapling from the center out on the underside of the frame. Be sure to pull everything as tightly and evenly as you can.
Tuck the extra fabric along the sides of the foam. The tension of the front and back staples will hold it in place.
The corners can get messy, you need to cut them a bit. At the front corners where the braces meet, cut a diagonal slit before stapling the fabric to the frame. This will prevent pulling and bunching.
Cut the excess fabric off the frame. Since we were generous with the overhang on the front you’re likely to have 10 or so inches hanging down that needs to be cut off.
You built a bench! How cool are you? And how pretty is this bench???
For more on the entire closet book nook build, check out this post.
Enjoyed the project?
Resources for this project:
See all materials![Brianna at Bloom in the Black](https://cdn-fastly.hometalk.com/media/profile/2020/05/12/43103625_3.jpg?size=91x91)
Comments
Join the conversation
-
Linda Abate on Aug 06, 2021
This is a great idea making a reading nook especially if there is another closet for her clothes. Another thing that can be done, once she is a bit older, is turn this reading space into a built in desk for homework. You already have open shelves for a clock, pens/pencils and supplies. Love this use of space.
-
Brianna at Bloom in the Black on Aug 06, 2021
I love that idea!
-
-
-
Valerie Burge on Aug 05, 2022
I wish I had done something like this for my daughter when she was younger. She loved hanging out in her closet. Now she's a tween and the same height as me, so I missed that boat! LOL You did an awesome job!
-
Brianna at Bloom in the Black on Aug 06, 2022
Hahaha thanks Valerie!
-
-
-
Frequently asked questions
Have a question about this project?
Where do you put her clothes?
How would you do it if one of the sides butts up to a cabinet instead of a wall?
What sort of lighting do you have in the reading nook?
Do you have a separate light fixture?