Maybe you don't have to fill in the gaps! You could take the doors off and have a good space for a garbage can! Looks like an incomplete cabinet with no bottom floor in it but there is kitchen flooring in that space. You could also add a 1x4 or a 1x6 across the bottom horizonally and construct or buy bigger doors. You could add a center stile vertically in the middle of the doors as well. New doors would then hit those added pieces when closed.
You could take the measurements and add a shelf under the sink to keep things off the floor, such as cleaning supplies. The 2 doors could come off and put a curtain held in place be a tension rod or follow Gk's suggestion.
Strange. Like there was something built in the cabinet or added on. You can do what Gk suggest if your handy. A board across the bottom and a center board between the doors. A quick way would be to remove the doors and hang a curtain
As there is no vertical support in the centre of the two doors to mount anything, I would
-first remove the doors and hinges completely.
-add a narrow shallow piece of wood to each outside where the hinges are presently
-add another narrow shallow piece of wood over top of the horizontal piece under the counter top
-remount the two doors and hinges on to the new pieces of wood, slightly lower height than they are presently
-this would eliminate the gap in the centre, and would also cover the potential gap across the top if you were to mount the doors at exactly the same height as they are now.
You can put a "stop" between the two doors by attaching a 1 x 2 or 1 x 4, whichever size you need. Then add plywood to the bottom. If you want to dress it up, add an applique to the board.
why not just replace the doors with a new stop between them? measure the opening and get new doors and if you get unfinished ones you can paint them any color you like and my second suggestion is take the doors off and add fabric to a tension rod to hide the opening
Hi Karen, you can create a new horizontal support and add a vertical crossbeam stop between the doors. Measure the width and height of the gap at the bottom, add about 4" to the measurements and cut a piece of wood to size. Paint the horizontal support and insert and screw in from the inside of the cupboard. Next measure the vertical gap between the doors add 2" to the width and 4" to the height, paint and screw in. Hope it helps
Measure the size and ask for a scrap piece of wood in that size at your local hardware store. They have a pile of scraps and are more than happy to cut wood for you. You can use wood glue and slide the wood into place.
Hi ! Either measure the space and go to home depot and have them cut a piece of wood for new doors . Go when they aren't busy . Or you can just buy a piece of wood that would be a little wider than the gap , then set it in place with the frame work , in fact there usually is a piece of wood there in that space as part of the framework / support of the cabinet . Maybe a previous owner took it out to work under the sink ??? Good luck !
My daughter has a cabinet like this and someone before her just took a small piece of wood and attached it to the back of the left door so that ends up being the door shut first. When you close the second door you don’t see between the gap. Depending on your skill level and tools this might be an easier fix than others suggested
Are the doors hung right? Maybe they just need to be unscrewed and moved over a little bit? That happens to mine all the time. If not then I would cut a 1x2 piece of wood and attach it in the center. Paint it white to match the cabinet.
install a piece of wood 1x2 or 1x3 to fill it in and doors will have something to butt up against ;add magnetic closure so they will stay shut (if needed)
Just remove the two doors, hinges and all, fill the holes, paint and hang a tension rod across the area just beneath the top board and add a curtain the correct size. A shelf across the entire inside will provide you lots of storage space. Use the 2 cabinet doors for a diy project such as making a couple of trays, art work, etc.
Place a piece of latice wood on the inside of one door and on the outside of the other one which would create an over lap and you could add magnetic catches top and bottom to secure the doors to each other.
OK, I spent a week and a half bottle capping this table top, even longer collecting the caps. I am so terrified of pouring resin on it and messing it up. I got... See more
I have an office chair that I use in my sewing room/office and recently it has been leaving black marks that look like oil. Can anyone tell me how to stop it from... See more
Hi DIYers, I would like to know the details below.What kind of Stencil should I use to paint over my Canadian Oak Almirah?Which category of paint is suitable if I... See more
Hello,I recently screwed through a laminate table top due to my error of not fixing washers to the underside of the brackets.Is there anything that can be done to... See more
ok So my question is on how to redo a kitchen table. I saw y’all sanded then painted white. Then added stain on top then topped with polycyclic. What type of paint do... See more
I have bee told that that mixing steel wool will do something to wood. I don't know it does or how to do it. I'm hoping someone can help me. What do I do and how do I... See more
We have a California King mattress set inside a waterbed frame. It's so hard to make the bed. Have to lift the mattress out of the frame. Can't really afford a new... See more
I am in a wheelchair and i wanted to know if there is any hometalker out there that knew what the best thing was to use to clean it with? Please Help me! Thanks a... See more
I LOVE to do DIY projects (or try to) on everything! I've just heard of painting upholstery & loved the piece you shared when you did a chair & free handed flowers on... See more
I just bought an outdoor plastic lighted Santa that is in desperate need of paint. The problem is it looks like others have tried but the paint didn't stick. Plus, I... See more
My wife has wanted me to chalk paint the bed for a long time. I have been putting it off. I finally got around to it and she loves it. What do you think about it?
These dressers have cup pulls that seem to be recessed or “pressed in” and I’m not sure how to remove them. Id be fine having to do some filling with wood filler... See more
I have a really expensive leather Cabot Wrenn executive chair that is the wrong color for the room it will be placed in. I do NOT want to ruin it and have heard... See more
After using CitriStrip, What is the best way to get rid a any dried on residue in small crevices? The piece I stripped has a lot of detailed areas where I didn't... See more
How can I repurpose this significantly sized playhouse on stilts for my use and to be more attractive in our yard? I can climb the vertical 7’ ladder, but no one else... See more
Karen: you could take doors off and hang a curtain rod with gathered curtains
I like that ideal TY so much
Maybe you don't have to fill in the gaps! You could take the doors off and have a good space for a garbage can! Looks like an incomplete cabinet with no bottom floor in it but there is kitchen flooring in that space. You could also add a 1x4 or a 1x6 across the bottom horizonally and construct or buy bigger doors. You could add a center stile vertically in the middle of the doors as well. New doors would then hit those added pieces when closed.
Thank You
You could take the measurements and add a shelf under the sink to keep things off the floor, such as cleaning supplies. The 2 doors could come off and put a curtain held in place be a tension rod or follow Gk's suggestion.
Strange. Like there was something built in the cabinet or added on. You can do what Gk suggest if your handy. A board across the bottom and a center board between the doors. A quick way would be to remove the doors and hang a curtain
As there is no vertical support in the centre of the two doors to mount anything, I would
-first remove the doors and hinges completely.
-add a narrow shallow piece of wood to each outside where the hinges are presently
-add another narrow shallow piece of wood over top of the horizontal piece under the counter top
-remount the two doors and hinges on to the new pieces of wood, slightly lower height than they are presently
-this would eliminate the gap in the centre, and would also cover the potential gap across the top if you were to mount the doors at exactly the same height as they are now.
You could add a piece of wood in the center to fill-in the gap.
Yes, however, as there is no horizontal support at the bottom, it will be very difficult to keep the vertical piece in the centre anchored in place.
Yea cuz the piece that was their was terrible looking and it was like stapled or something 😠
You can put a "stop" between the two doors by attaching a 1 x 2 or 1 x 4, whichever size you need. Then add plywood to the bottom. If you want to dress it up, add an applique to the board.
why not just replace the doors with a new stop between them? measure the opening and get new doors and if you get unfinished ones you can paint them any color you like and my second suggestion is take the doors off and add fabric to a tension rod to hide the opening
Hello. A flat piece of lattice wood would could possibly be under-mounted and painted white.
Hi Karen, you can create a new horizontal support and add a vertical crossbeam stop between the doors. Measure the width and height of the gap at the bottom, add about 4" to the measurements and cut a piece of wood to size. Paint the horizontal support and insert and screw in from the inside of the cupboard. Next measure the vertical gap between the doors add 2" to the width and 4" to the height, paint and screw in. Hope it helps
Measure the size and ask for a scrap piece of wood in that size at your local hardware store. They have a pile of scraps and are more than happy to cut wood for you. You can use wood glue and slide the wood into place.
Hello Karen,
Seems as though the central brace, floor and plinth of cabinet has been removed!
Just need to replace them..........
Hi ! Either measure the space and go to home depot and have them cut a piece of wood for new doors . Go when they aren't busy . Or you can just buy a piece of wood that would be a little wider than the gap , then set it in place with the frame work , in fact there usually is a piece of wood there in that space as part of the framework / support of the cabinet . Maybe a previous owner took it out to work under the sink ??? Good luck !
My daughter has a cabinet like this and someone before her just took a small piece of wood and attached it to the back of the left door so that ends up being the door shut first. When you close the second door you don’t see between the gap. Depending on your skill level and tools this might be an easier fix than others suggested
I would hang a curtain on it. I have done it with rods and without. So easy...and still functional.
Leave doors on:https://www.exquisitelyunremarkable.com/2018/06/easy-to-open-kitchen-sink-skirt.html
Remove doors: https://www.exquisitelyunremarkable.com/2014/07/easy-skirted-table-tutorial.html
No doors, ring clips: https://www.exquisitelyunremarkable.com/2014/11/ring-clip-skirted-table-easy-diy.html
I'd add a wooden slat.
?
Are the doors hung right? Maybe they just need to be unscrewed and moved over a little bit? That happens to mine all the time. If not then I would cut a 1x2 piece of wood and attach it in the center. Paint it white to match the cabinet.
install a piece of wood 1x2 or 1x3 to fill it in and doors will have something to butt up against ;add magnetic closure so they will stay shut (if needed)
All you need to do is put a piece of flat wood in the middle and make sure the doors cover the edge. Paint it the same color as you cabinet.
Just remove the two doors, hinges and all, fill the holes, paint and hang a tension rod across the area just beneath the top board and add a curtain the correct size. A shelf across the entire inside will provide you lots of storage space. Use the 2 cabinet doors for a diy project such as making a couple of trays, art work, etc.
Place a piece of latice wood on the inside of one door and on the outside of the other one which would create an over lap and you could add magnetic catches top and bottom to secure the doors to each other.
I would add a board in the middle to create nice conversations