Reupholstering a Dining Chair - Family Heirloom

6 Materials
$100
1 Week
Medium

I inherited a number of antique furniture pieces from my Grandparents.


I have had this formal looking dining room chair – is it maybe called a Carver’s Chair? – for years now.


I’ve always intended to re-cover and re-upholster it but it’s taken me a while to get around to it.


This was the week!

My Grandparent's chair before!

The first thing I did in my quest to reupholster my dining chair was to remove the old fabric by prying out the nails and staples.


I have a good staple remover but it still took me some time as they’d been in there awhile!

I followed the advice in another  upholstery tutorial on Upcycle My Stuff that says it is best practice to save the old fabric as you take it off so you can use it as a pattern piece for your chair.

If you think about it, somebody ages and ages ago already did the measuring and calculating of how big that piece of fabric should be and how to cut out the corners – so it makes sense to just trace the old piece of fabric when cutting your new fabric!

I also removed the old padding at this point.

When I stripped the fabric off of the armrests of this old chair I discovered that there were wooden blocks attached to the arms of this chair that seem to have been added after it was made.


They were probably added the last time it was recovered in the 1950s – most likely by my Grandfather!

The previous fabric on the armrests was well worn on the corners from these wood pieces so I decided to sand down the corners of these sharp rectangular blocks of wood with 60 Grit sandpaper.

I knew before I started this project that I wanted some additional cushioning on the armrests as they always felt a bit hard to me – that will have been that hard wooden block underneath!


I did staple on some new padding but it still didn’t seem ‘cushy’ enough so I added in some old (but freshly washed!) socks.


I cut the socks into rectangular pieces that fit around the wooden blocks. Turns out they were just the right size for what I needed!

I put another layer of the cotton padding on top of the socks.

For the chair and seat back I went ahead and removed the old padding and replaced it with new cotton padding. I went as thick as I felt I could go with it and ended up adding a couple of layers.


I stapled it in place following the existing staple line for the old seat padding.


When all the padding was secured in place I cut off the excess padding around the edges with an exacto knife (craft knife in the UK).

I chose a bold blue and white art deco fabric. My apartment is mostly greys, teals and blue shades so it fits in well.


I wanted to leave the wood as it was rather than paint it as it is in good condition (plus my grandfather was not a fan of painted wooden furniture!).


I decided to pick a really bright and striking fabric so that it still ended up looking more modern even with the wood finish.


When I first started I stapled on the fabric and cut of the excess as with the padding however that caused the fabric to pull.


So then I started to fold the edge under and then staple it to the frame.


I stapled into the same spots/lines that the previous staples were located

Tip: Be careful to line up the fabric and place staples at the mid lines on each side first and then staple along the edges.


The last step is adding the trim!

Once you have your upholstery fabric secured you will still have a visible staple line so this needs to be covered with some trim.


There are lots of different varieties on the market – I went with the hammered stud style trim.


These studs come in a long roll. Every fourth or fifth stud has whole in it and you also get a pile of loose studs with sharp nails on the end.


These go through the holes and you hammer the whole strip down just at these points.

The strip of studs cut and bend easily, so they are quick and simple to work with.


You simply measure, cut, place it over your staple line and use a hammer to hammer in the studs that have the nails/spikes on them.

My last step was to re-cover the underside of the chair seat. 


I actually decided to add more padding at this point so I shoved it in from below under the springs and smoothed it out. 

I used some of fabric I had taken off of the chair (a piece that was in the best condition) and added it to cover the underside.


I thought this was a little ‘added upcycle’ and also a way of keeping a bit of the chair’s history!

I am so pleased with how this turned out!

Obviously I was nervous recovering such a family heirloom. The new fabric just blends in so much better with my home decor and I think my Grandparents would be so happy I am keeping their chair in the family too!

If you liked this project you might like some of the other upholstery tutorials on Upcycle My Stuff too!

Resources for this project:

See all materials
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page.More info

Kristen Hubert
Want more details about this and other DIY projects? Check out my blog post!
Go

Frequently asked questions

Have a question about this project?

Comments

Join the conversation

2 of 50 comments
  • Karen Bosco Karen Bosco on Dec 12, 2020

    You did a professional job. It is beautiful!

  • Maggie Maggie on Dec 27, 2020

    Beautiful! You did a fantastic job on this wonderful heirloom and the fabric is awesome. Congrats on a job well done and preserving a family heirloom!

Next