Madilyn
Madilyn
  • Tutorial Team
  • Warren, MI

Update Your Ugly Ceiling Fans!

4 Materials
$15.00
4 Hours
Medium

I used to open my eyes every morning after a night's sleep only to be greeted by my VERY ugly ceiling fan. Not anymore! Check out my easy updates.
The finished product in my "bird room"
I started by removing JUST THE BLADES, not the entire fan. Each blade was held on with just two screws. Who knew?

Next I dusted and and cleaned both sides of the blades with a good de-greaser like Crud Cutter. This made it possible for the paint to stick on the sides of the blades without peeling off later. Also. you will need to remove the "arms" on each blade. You can paint them if you wish. I used chalk paint which covers great and doesn't require any prep work or sanding.

Now the fun part! I decided on a theme/color scheme. In this case bird/old-fashioned theme in turquoise and cream colors. Next I flipped through my $5 Walmart scrap booking paper books for potential candidates. If you aren't sure about what colors will match each other either do each blade the same or use paper from the same book. Most books carry pages in the same color family. In my case I used various papers I already had from other projects.

Once you have your papers, you will need to play around with them to makes sure that you have enough paper not only to cover the blade but also so match the pictures in the case your blades are longer than the standard 12 in x 12 in scrap book pages. If you don't feel comfortable having the skill to match, you can use wrapping paper, contact paper, or scrap book paper that is made up of random or repeated shapes and is already distressed looking. Here is an example of another blade from a different fan. Since the paper was already patchwork, it is harder to see the seams.


This paper already has built in seams!
Now the work begins. Lay out the blades on each page of paper. Make sure to take into consideration the placement of any pictures. On this blade I wanted to make sure the bird was on the largest part of the blade because I thought it was the prettiest part.
Keep placement in mind before cutting
Alright, by now you should have an approximate idea of placement of paper on each blade. You can skip this next step if you want to. In fact, it took me 2 fan projects to even realize this WAS a step. If your blades are those ugly fake wood like mine were, you might want to paint the edges of each blade with the color of EACH PAPER that will be place on it. If you skip this you will just have the wood peeking through on the edges of each blade. It is a matter of taste and in my case laziness! lol
Can you see the brown, wood edges?
OK, now I am going to share a secret with you. This will make the difference between clean, finished edges without bubbles on the paper and a poorly cut lumpy blade. Trust me. Once I discovered this secret I redid all of my previous work and it was worth it.

Notice how my laundry room blade doesn't look like a 2nd grader cut it? To achieve that effect you need to leave about a quarter to a half inch of over hang on each side of the blades. The second half of the secret to alleviate the bubbles is to run your paper under warm water for a second. Make sure it isn't soaking wet, just slightly damp ALL OVER. If you miss any spots, these will bubble up. Relax, your picture will not disappear off of your paper! Work on one blade at a time. While your wet paper is "curing" you can spread a thin coat of Mod Poge on the blade. Only spread on the section that is going to be covered by the ONE sheet of paper you just got wet. I always go about a half inch past the seam but no more.
Using distressed paper helps hide mistakes!
After you have attached all of the paper, making sure to match up the seams if necessary, (don't overlap if possible) you can gently push down on the paper with a damp sponge. This will smooth out the paper.

Next, GENTLY use a 320 grit sanding block to lightly sand the overhang paper around each blade. That is what gives the clean edge. It is easier to do if the paper is still slightly wet. Repeat with each blade and before you know it it will be time to lightly coat the dried blades with a few sealing coats of Mod Podge, put the blades back up and enjoy your hard work!
My USA themed room.

Suggested materials:

  • Screwdriver, sanding block, foam brush  (Lowes)
  • Scrap book paper (5 sheets), chalk paint. Mod Poge  (Walmart (I used paper from 3 different books which cost $5 ea)
  • Measuring tape, scissors, pencil. sponge  (Had on hand)
See all materials

Top Hometalk Projects

30 Fun Ways To Keep Your Home Organized
30 Ways To Use Old Jeans For Brilliant Craft Ideas
31 Creative Garden Features Perfect For Summer
21 Totally Terrific Things You Can Do With Doilies
15 Fabulous Fire Pits For Your Backyard
15 Amazing Things You Can Make With Dollar Store Gems
30 Unusual & Helpful Gardening Tips You'll Want To Know
17 DIY Projects You Can Start And Finish Tonight
30 Creative Ways To Repurpose Baking Pans
21 Totally Terrific Things You Can Do With Doilies
15 Kitchen Updates Under $20
30 Brilliant Things You Can Make From Cheap Thrift Store Finds!
16 Creative Ways To Upcycle Pallets
31 Amazing Furniture Flips You Have to See to Believe
30 Essential Hacks For Cleaning Around Your Home

Have a question about this project?

Join the conversation

2 of 9 comments
Your comment...