Remodelling The Old Nasty Carpeted Bathroom Floor

6 Materials
$400
2 Days
Easy

Some easy steps to remove old nasty bathroom carpet and remodel the bathroom floor with great looking tiles. These steps are as follows:

how to remodel old bathroom floor

Step 1: Remove the old ugly looking carpet

Start taking off carpet from one corner or either cut it into small six inches pieces using utility knife and pull it out.

how to remodel old bathroom floor

Step 2: Clean or vacuum the area after removing carpet

Once the carpet is pulled off and floor is down to nothing but plywood subfloor, sweep the area clean or vacuum to make sure the area is free of debris.

how to remodel old bathroom floor

Step 3: Measure the dimensions and cut cement backer board

Measure the dimensions using measuring tape down to a quarter inch space and cut the cement backer boards accordingly.

how to remodel old bathroom floor

Step 4: Lay down the backer board

While laying the boards, use full sheets so that you can have as short of joints as possible. Make some cuts where necessary and cover the floor completely.

how to remodel old bathroom floor

Step 5: Repeat Step 2

Now as the board is laid down, make sure the area is clean and there is nothing between subfloor and cement boards.

how to remodel old bathroom floor

Step 6: Make a mixture of modified thinset and water

Take modified thinset that is used to prevent any cracking down the road, add water into it and make a mixture of perfect consistency.

how to remodel old bathroom floor

Step 7: Swap the mortar down onto the floor

Now remove board one by one. Then start swapping the mortar onto the floor and spread it around.

how to remodel old bathroom floor

Step 8: Lay the boards down onto the floor

After spreading mortar, start laying boards. Once all the boards are laid down, walk on it so it has good bond to the subfloor.

how to remodel old bathroom floor

Step 9: Lock boards using nails

Now as all the boards are on place, lock them using roofing nails and drove them roughly every 12 inches.

how to remodel old bathroom floor

Step 10: Choose your tile layout pattern

Taking a chalk make a straight line in center and start placing your tiles accordingly. Choose the layout of tiles you want place them Don’t worry about the extra spaces.

how to remodel old bathroom floor

Step 11: Measure the extra areas around

Once you have placed all the tiles according to the layout you have chosen. Measure the extra area left around the tiles and cut the tile as per the measurement and place it over there.

how to remodel old bathroom floor

Step 12: Apply mortar on the floor

Now spread mortar on the floor and start placing tiles over it one by one.

how to remodel old bathroom floor

Step 13: Grout the area

After laying all the tiles, leave it to rest for a day and now apply grout down into it to fill the spaces or joints in the tiles.

how to remodel old bathroom floor

Step 14: Clean the gout on the tiles

Last step is to clean the gout spread over the floor using warm water and sponge. Make sure you clean it up in an angle of 90 degree so that you will not remove the gout from joints.

Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page. More info

To see more: https://milmandesignbuild.com/

Have a question about this project?

3 of 4 questions
  • Brenway
    on Apr 14, 2019

    I pulled old tile up from my laundry room but can not get the sticky clue to come up!! Any suggestions

    • Robyn Garner
      on Apr 16, 2019

      I had the same issue in my kitchen when the individual vinyl tile corners all lifted due to a power outage that defrosted the freezer onto the floor. We had to work on individual pieces of plywood to keep ourselves from sticking to the floor!


      As we chose to put in a laminate floor, we ignored the glue residue and CAREFULLY laid down the underlayment foam for the floating floor and proceeded from there.


      Hope this helps! 😎

  • Geo31102094
    on Apr 16, 2019

    In step 7 you are saying to swap the boards and the floor. I presume you mean SWAB the boards and floor. If not then I have no idea what you are telling me to do.


    • Sharon
      on Apr 20, 2019

      I think he meant slap some mortar on the floor. Slap it on the floor and spread it around.

  • Gary Olver
    on Apr 16, 2019

    You didn’t say what size notch trowel to set the cement board ! Why are you not using hardie board and what size half or quarter ! Yes wet the cement or hardie board for a better bond !

Join the conversation

3 of 8 comments
  • Lailoni Muscaro
    on Apr 13, 2019

    I have a toilet in my old bathroom and am wondering how would the additional height affect the seal between the wax ring and the toilet that sits on it? It looks like there might be approximately 1" of extra height with the thinset, cement/backer board, mortar and tiles and from what I can see, it looks like I only have plywood, adhesive and linoleum installed from decades ago in my bathroom (The floor from the bathroom is slightly higher than my hallway and after removing the strip that covered the gap, I lifted up a piece of the linoleum to check). Any feedback or suggestions is appreciated.

    • Connie Peters
      on Apr 14, 2019

      They make a type of toilet ring that is adjustable, not the wax ring style. No nasty wax to scrap out. Makes it easy if you ever need to pull toilet down the road.

  • Alice
    7 days ago

    You did a beautiful job

Your comment...