Make A Silicone Concrete Planter Mold From PVC

24 Materials
$40
3 Hours
Medium

Make A Silicone Concrete Planter Mold Using PVC Pipes. Add A Pottery-Looking Glaze!


So not only can you create a concrete planter from an existing object using silicone (like I did here- Textured Silicone Cement Planter), but you can also make a silicone mold for pots from pretty much any type of supplies. This one I made using two different sizes of PVC pipe that is cut to size. Making a mold for cement planters doesn’t need to be complicated. And then you can make multiple copies of the planter and decorate them in different ways.


** If you love cement projects, you may want to see my articles on comparing the different types concrete mixes and working with molds and pigments, too! There, you'll be able to grab my free Pocket Guide to Concrete & Cement Mixes For Crafts .


I have always loved the look of glazed pottery, so I decided that’s what I would do here. An easy and incredibly fun way to do this is to use resin. Painting this was actually a breeze.


Epoxy resin has some very forgiving qualities because it self-levels which makes it perfect for getting a nice even coating. If you layer it up, you can make such incredibly beautiful designs. I keep it simple for this tutorial, but if you see where I have the resin layered up more, it can really bring out nice colors and such a cool pottery glaze look.

CUT THE INNER AND OUTER PVC MOLD PIECES


The 3” wide pipe will be the outer mold and the 2” piece will be the inner mold. Using a miter saw, cut the 3” PVC to 3 ¼” long and the 2” PVC to 2 ⅞” long.


Take a rigid board like a piece of plywood and place it on your work surface. Next, cut a piece of acetate that is 5×5” and lay it on the rigid board. Tape it in place with blue tape.


Now take a piece of the oil based clay and roll it into a ball and place it onto the acetate. This piece needs to be a bit wider than the diameter of the outer mold piece. Flatten it a bit with your hand, and then use a rolling pin to get it to about ¼” thick. Take the 2” inner mold and place it in the center and press down. 


I didn’t do it this way but realized it would have been better afterward.

SECURE THE SILICONE MOLD CONTAINERS

Take the 3” outer mold piece and center it over the inner mold, but don’t press down yet. First, trace it and then remove it. You are just making sure you have it fully centered. If it looks centered, then go ahead and press it into the clay. If not, then adjust as needed. 


Remove the excess clay around the outer mold and then use hot glue to glue the outside of the mold to the acetate base. Add some clay around this and pack it in to help with potential leaking.

CREATE THE DRAINAGE HOLE AND LUBRICATE THE MOLD

Insert the straw through the middle center of the inner mold. Trim it to get it out of the way, make it about an inch or two taller than the outer mold.


Take vegetable spray and liberally spray inside and outside the inner mold and inside the outer mold.

COMBINE AND POUR THE SILICONE

Check to see how much mold material you will need. You can find an online calculator on Smooth-on's site 9they make this brand of mold). In a big disposable cup, mix equal parts of the A & B silicone. Be sure to stir each individually before mixing them together. 


Pour the mixture into the mold, starting from the inner mold and then into the outer mold. Let this cure approximately 6 hours.

REMOVE THE PVC FROM THE SILICONE PLANTER MOLD

Peel back the acetate sheet, then pull out the straw. If the straw doesn’t come out easily, grab it with needle nose pliers. With the pieces being lubricated, this should demold fairly easily. It may help to have a second set of hands, one can push while the other pulls. 


If you have trouble, then clamp the PVC to the table and use a hacksaw to carefully cut through the outer pipe. Split it apart and pull out the mold. The inner PVC mold should come out without much trouble.

CAST THE CEMENT PLANTER

Note: You are welcome to use lubricant for the cement, but it tends to cause little pinholes when you do. 

Place a rigid board on the work surface and place the concrete planter silicone mold on that. Mix the cement and be sure it’s fluid enough to pour, like a milkshake consistency. 


Use a craft stick if necessary to push the cement down in between the voids. Fill the cement mixture to the top, then lift, tap and shake the board, and tap the sides of the mold to fill the voids. 

Let this cure for a couple of hours.

REMOVE THE PLANTER FROM THE PVC SILICONE MOLD


Get a towel or cloth and demold it over that to help cushion the planter. Use a sanding sponge to sand any sharp edges.

PAINT THE CONCRETE PLANTER WITH RESIN

Now it’s time to decorate the planter. It will be easiest to paint if you place something inside to help it stand up (upside down). A spice jar was the perfect size. This gets a bit messy, so if it’s a jar you want to hang on to, I recommend wrapping it in plastic wrap to protect it.


You’ll also want to place something underneath because this will definitely cause a few drips. The rubbing alcohol is for clean-up. I usually pour a little into a glass or ceramic bowl and dip my Q-tips or paper towels in that when things get messy.


Mix up the resin using a craft stick, at a 2:1 ratio, and for two full minutes- I told my phone to set a timer for me :0). I used about 20ml total of the epoxy. 

Now mix in a color, I used blue. This concrete planter was naturally very beige, and so when painting it with blue resin, it turned a bit green. If you want it more opaque, then just add a touch of white to the color you use.


You only need a tiny bit of color, so dip a toothpick into the colorant and mix it in with the epoxy. I dipped my toothpick into the color twice to get it the color you see here.

Now use either a craft stick or a paintbrush to brush on the resin. If you start at the top (which currently is really the bottom since it’s upside down), then the resin will drip once it hits the rim of the planter. That’s okay, let it be for now. 

*One important thing to note, is that the bumped out rim of the concrete planter that you see on the top of the planter is actually resin (at the bottom in photo). This will happen naturally because it’s where the resin will mound up. It’s part of what I really like about how this turned out.


Work your way around the cement pot until it’s covered. After a little bit of time, you will see that it starts to even out and the unevenness mostly, if not completely, goes away.


If you’re wondering what the blue stuff is on the bottom of the planter (top of photo), it’s extra resin I put on that spot because the board I used for letting my planter cure, was warped and caused the bottom to not be level. This resin shimming trick worked pretty well.

You can add a second layer if you want it more opaque or darker. Now to deal with those drips, take a craft stick and put it under the rim and just scrape the drips off. You will likely need to do this multiple times. I recommend switching to a Q-tip as the drips slow to refine it. 


Keep an eye on the drips for up to 15 minutes after you paint it. If you leave them, then they will harden and you’ll have drip bumps hanging off the rim. And now at this point, you should be able to carefully flip this over and touch up the areas of the rim that still need the resin.


After that, wait 2-3 hours and it should be dry, but be careful not to handle it much until about 24 hours later when it has completely cured, or you risk getting fingerprints in the resin.


After 24 hours, the epoxy resin should be super hard, so go ahead and add plants to your concrete planter, made from a PVC silicone mold.

Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page. More info

Top Hometalk Projects

30 Great Mason Jar Ideas You Have To Try
Storage Hacks That Will Instantly Declutter Your Kitchen
31 Ways To Keep Your Home Organized
31 Creative Ways To Fill Empty Wall Space
3 Easy Ways To Upgrade Your Pillows To A High End Look
Make Your Kitchen Beautiful With These 15 Inexpensive Ideas
These Stunning Seating Ideas Will Blow You Away
31 Update Ideas To Make Your Kitchen Look Fabulous
Try These Gorgeous Ideas And The Mailman Will Never Miss Your Mailbox!
31 Clever Ideas To Reuse Muffin Pans And Cupcake Liners
Browse Through These Dream Bedrooms & Find Your Favorite!
15 Amazing Craft Projects That You Can Do Under 15 Minutes
22 Homemade Soaps You Can Give As Gifts All Year Round
30 Essential Hacks For Cleaning Around Your Home
Fun Father's Day Gift Ideas You Can Make Yourself
Artsy Pretty Plants

Want more details about this and other DIY projects? Check out my blog post!

Go

Have a question about this project?

3 questions
  • Gail
    on Aug 11, 2020

    Why not just paint the PVC after you put the bottom on...with the epoxy if you are looking for the shiny look?

    • Artsy Pretty Plants
      on Aug 12, 2020

      Because plants are much more happy (especially succulents) in a concrete planter than a plastic one. This will last for decades, I'm not sure how great the PVC will look. In any kind of wind, the plastic one will tip over.

  • Carolina
    on Aug 11, 2020

    Nice but I don't get it. With the cost of the epoxy wouldn't it be easier and cheaper to just buy a planter? Looks like way too much work for what you get. It turned out pretty though.

  • Sandra Whittier
    on Aug 11, 2020

    Why not color the resin?

Join the conversation

Your comment...