Tilt-out Cabinet Trashcan

22 Materials
$0
2 Days
Advanced

Looking to hide your unsightly trash bins? Why not do so by blending them perfectly to the rest of your custom-built cabinets in your kitchen. For this project, we recommend using a double bowl vanity which can be purchased from CabinetNow.com along with the custom made doors, drawer fronts, and drawer boxes.

Let’s start this handy project by making sure that you have all the required materials to begin.
Staining Materials
  • Wood Stain
Choose a stain color that will match the rest of the cabinets in your kitchen.
  • Clear Polyurethane
This will protect your cabinets from water damage while adding a nice finished shine to your project.
  • Multipurpose Rags
  • Gloves
Assembly Materials:
  • Double Bowl Vanity
15 inch depth
  • 2 Cabinet Doors
width: 19.5” height: 24.5”
  • 2 Drawer Boxes
width: 17.5” height: 4.25” depth: 13”
  • 2 Drawer Fronts
width: 19.5” height: 6”
  • Four Drawer Slide Sockets
Slide Sockets keep the drawer slides and drawer box in place by fixing the drawer glides to the rear of the cabinet box.
  • Four Drawer Glides
Measure the depth of the cabinet box before purchasing the sliders to make sure they fit just right. For our project, we used 14” universal side mounted drawer glides
  • Two Trash Cans
Be sure to measure the height of the trash cans to ensure they fit to the inside of the door and allow for the doors to swing open once attached. For our project, we used 2 10 ¼ gallon trash bins
  • 10 Feet of Chain
The chain will be cut into 6 pieces. Two pieces to secure the trash cans to the door and four pieces to secure the doors (two on each door) to the vanity.
  • 4 Middle Hinges
There will be two hinges placed at the bottom of each door to make for a smooth open and close.
  • 8 Sheet Metal Screws
These screws will be used to secure the chains to the doors and cabinet box.
  • 4 Cup Hooks
The use of hooks to chain down the garbage cans will make for easy trash removal.
  • 2 Door Handles & 2 Drawer Knobs
Try to get handles that fit your personality and compliment your kitchen!
  • 2 Door Magnets
The magnets will keep the doors from swinging open under the weight of the trash.
  • Optional Finishing Washers
These are optional and can be used to protect the wood when screwing the chains into the doors and cabinet box.
  • Tools
Screwdriver/cordless screwdriver and something to cut the chain with.
Assembly
Check out this article on how to assemble your custom-made cabinet box from CabinetNow.com. http://www.cabinetnow.com/how-to/guides/how-to-assemble-vanity-boxes

Now that you have assembled your Double Bowl Vanity, it is time to turn it into your very own Secret Trash Bin. A lot of this project is customizable as you will want your trash bin to blend seamlessly with the rest of your kitchen cabinets.

Prepping your Work Station
The first portion of this project involves stain and a polyurethane spray so be sure to set up your station in a well-ventilated area or outside. Both items can create quite a mess so be sure to lay down plenty of cardboard under and behind the vanity, drawer fronts, drawer boxes, and the cabinet doors. Always wear gloves and protective eye-wear when using stain to reduce the risk of injury.
STEP 1: Staining your Vanity and Doors
  • Place the vanity, drawer fronts, and cabinet doors on a safe work surface. The easiest method is to open the cardboard box that the vanity came in and lay it flat on a work surface.
  • Begin staining by dabbing the rag into the stain can and, using long strokes, rub the stain into the wood. Wipe excess stain off and do not let the stain sit for too long on the wood to avoid uneven staining.
  • Once the vanity, drawer fronts, and cabinet doors are all stained and match in color, let them sit until dry.

STEP 2: Sealing your Vanity and Doors
  • Once the stain has dried, it is important to seal the entire vanity, drawer fronts, drawer boxes, and cabinet doors with polyurethane. This protects the wood from water damage and gives the entire project a glossy finished look.
  • Spray the Polyurethane gloss in long and even strokes to achieve the best finish. Be sure to wear protective gear when using the spray.
STEP 3: Fitting your Drawers
  • Take the glide sockets and position them on the back of the vanity where there are pre-notched holes for drilling. The sockets should be facing glide side in toward one another. Be sure to line up the glide sockets with the face frame of the vanity to ensure your drawers will lie evenly. Drill them into place with the screws included in the slide socket package.
  • Now that all four glide sockets (one for each side of the drawers) have been drilled into the back of the vanity, it is time to attach your drawer glides. Each glide is labeled with an R for right or an L for left. Fit the correct sides into the glides and make sure they are level before drilling them into the face frame of the vanity. As seen above.
  • Take the drawer glides that attach to the drawer and place the glide on the bottom of the drawer box, with the wheels on the glides facing the back of the box. The front of the glide should come within a couple of centimeters of the front, but not extending past the box, while leaving a couple of inches hanging off the back with the wheel. Drill these into place, one on each side of the drawer box.
  • Slide the drawer boxes into place in the vanity and make sure everything is level.
Do not attach drawer fronts until after Step 5 to measure overlay accordingly.
STEP 4: The Cabinet Doors
  • First, measure out the middle of your cabinet door, where you would like to place your door handle. Drill in holes according to where your handle will screw into place. As seen above.
  • Place the trash bin on the inside of the cabinet door just above the frame This will allow for the door to fully swing open. Screw in a cup hook on each side of the trash bin. As seen above. Now remove trash bins.
  • Attach your hinges on the back side of the bottom of the doors, with the hinge’s leaf sitting flush to the edge of the door and the hinge’s barrel sticking out. The hinges are placed at 2 inches in.
  • Hold one of the doors in place along the bottom of the face frame, where it is to be attached. Measure to make sure the hinges are sitting at 1 ½ inches from the side of the face frame. This will leave a half inch overlay on each side of the doors. Drill the hinges in place.
STEP 5: Adding the Trash Bins
  • Measure out how much chain will be needed to wrap around the garbage bins, we used 33 inches of chain here. Cut the chain into the appropriate length (one for each bin), hook it into the cup hooks and then slide your bins into place. This chain will secure your trash bins to the inside of the cabinet door.
  • Cut the remaining chain into four 12-inch-long pieces. These will be used to keep the doors from swinging out too far.
  • Use the sheet metal screws to screw one end of the 12 inch chain to the door, next to the hook, and the other end to the inside of the face frame. As seen above. Repeat on each side of trash bin.
  • Lastly, attach one door magnet underneath the drawer face frame facing outward. Line up the matching metal piece to the magnet and screw it into the door. This will prevent the cabinet doors from swinging open under the weight of the trash.
STEP 6: Add your Drawer Fronts
  • Adding the drawer fronts to the drawer boxes is a little bit different in this project than a typical installation would call for. Because the cabinet doors will be attached with a hinge at the bottom of the doors, to allow it to pull forward, there will not be an overlay at the base of the door. This raises the overlay for the top of the doors, which in turn raises the overlay for the drawer fronts to ensure everything closes properly. Measure accordingly so your drawer fronts do not interfere with the cabinet doors.
  • Once the drawer fronts are attached to the drawer box, measure the middle of each drawer and drill through both the drawer box and the drawer front. Fit the knob in place.
STEP 7: Enjoy your New Secret Trash Bins
After installing the drawer boxes your secret trash bin will be nearly complete. To finish the project, pick out a counter top that will complement the rest of the room
Disclaimer
We have provided links to the exact product we used to achieve this beautiful finished project a the bottom of this article. The measurements used are for a basic height, double door cabinet but be sure to measure your kitchen before starting this project to make sure your trash can cabinets match the rest of your kitchen.

We also used Walnut wood to achieve this look. Price will vary by wood type and size of the cabinet box used. A single door Cabinet box would also look great and be as efficient.
Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.
Hometalk may collect a small share of sales from the links on this page. More info

Top Hometalk Projects

16 Creative Ways To Upcycle Pallets
15 Kitchen Updates Under $20
15 Affordable DIY Projects You Can Do Right Now!
13 Essential Repair Tricks That Everyone Needs To Know
31 Space Saving Storage Ideas That'll Keep Your Home Organized
31 Creative Garden Features Perfect For Summer
21 Totally Terrific Things You Can Do With Doilies
15 Pieces Of Furniture That DIYers Built From Scratch
16 Ways to Maximize Storage And Organization In Your Home
30 Ways To Use Old Jeans For Brilliant Craft Ideas
15 Genius Curtain Ideas To Instantly Upgrade Your Space
11 Unexpected Ways to Use Spices in Your Home
15 Amazing Ways To Get Your Patio All Ready For Summer
The Easiest Ways to Grow a Bumper Crop of Tomatoes
15 Kitchen Updates Under $20

To see more: http://www.cabinetnow.com/how-to/guides/how-to-assemble-vanity-boxes

Have a question about this project?

3 of 20 questions
  • Loriandnikki Ortiz
    on Nov 27, 2018

    How to stain kitchen cabinets

  • Gail Baker-Morehouse
    on Nov 28, 2018

    Why is everyone so critical in these questions? If you see it can be done cheaper or using other finds, just share your insights and share what might work easier or what type of old dresser one might use, etc. Gee-wizz.

    • Dede
      on Oct 14, 2019

      I think you though is great! I would turn an old dresser from the junk store sideways and the take the rest apart and jerry rig it, more fun and saves you $200.00

  • Stacy Wallen
    on Mar 2, 2019

    I have a dishwasher that no longer works and was thinking of doing this instead of replacing the dishwasher, would it be possible to do this with the cabinets and space where a dishwasher was?

    • Onwingandhoof
      on Dec 5, 2019

      Yes!!! I bought a small house and removed the dishwasher for that very reason. We bought a slide out trash. I attached it to the floor and had to build up the front of where you attach the door to make it even with the existing cabinets. After I got that done, I also attached a piece of baseboard to the bottom front so that when I pulled it out and pushed it back, it looked completed. There was also a large space above that so we built a large deep drawer since the kitchen only had 4 small ones.

Join the conversation

2 of 100 comments
  • Linda Abate
    on Oct 14, 2019

    Great job repurposing this old dresser. With people trying their best to recycle these days this is an awesome way to do so. It serves many purposes. It is lovely to look at, rather than yucky trash cans, and it keeps trash in one place.

  • Carla
    on Oct 15, 2019

    Clever you!

Your comment...